Key facts
- Manuals
- 5
- Models
- 1
- Languages
- EN · NL
- Last added
- 2023-10-19
Observator models by category
Featured Observator manuals

Observator OMC-7006 Buoy User Manual
The OMC-7006 is a buoy designed for water quality measurement, featuring an internal data logger (OMC-045-3), solar power supply, and optional alarm or navigational signal lights. The device includes a canister housing the electronics and a deployment tube for measurement probes, with solar panels attached to the outside to maintain battery charge.
The manual covers the assembly process using an EXO sensor as an example, detailed mooring procedures, and specific instructions for deploying and retrieving the buoy. It also includes sections on the No Alarm Disc function, the OMC-Programmer, maintenance routines, and opening the canister, along with circuit diagrams for various sensor interfaces.
Covers: Introduction · General description · Assembly of OMC-7006 · Mooring · Deployment and retrieval · EXO probe mounting

OBSERVATOR OMC-406 Temperature Humidity Sensor User Manual
The OMC-406 is a handheld sensor for accurate temperature and humidity measurements. It uses solid-state humidity sensors and a PT-100 temperature element for reliable data. The manual covers operation, measurement practices, calibration, and electrical connections. It includes technical specifications and precautions for accurate readings.
The sensor outputs 4-20mA signals for both parameters and requires a 8–26.5V DC power supply. Calibration is recommended annually, and the probe must be allowed to equilibrate with the environment before measurements. It is designed for use in gases and can handle air velocities up to 10 m/sec.
Covers: Introduction · Operation · Measurement Practices · Measurement in Gases · Calibration · Connections

Observator OMC-116 Ultrasonic Wind Sensor Installation Manual
This manual describes the installation of the Observator OMC-116 ultrasonic wind sensor. Installation must be carried out by a qualified engineer with basic knowledge of electronics. The document details pre-installation notes, including specific power supply requirements (12-15Vdc or 24Vdc depending on heating) and cabling specifications.
Covers: Pre installation notes & requirements · Terminals · Sensor installation · Cable connection · Alignment · NMEA output

OBSERVATOR OMC-045-II & OMC-045-III Data Logger Programming Utility User Manual
This user manual guides users through configuring and programming OMC-045-II and OMC-045-III data loggers using the OMC-Programmer 2010 utility. It covers setup steps including sensor configuration, email/FTP settings, and terminal layouts. The manual includes detailed instructions for basic configurations, advanced settings, and troubleshooting tips. It also explains how to connect sensors, manage power, and configure data transfer methods like GPRS or email.
The document is structured with sections on getting started, configuration options, alarm handling, and terminal pinouts. It provides step-by-step guidance for users to set up data logging, including sample rate, data storage, and transmission intervals. The manual assumes users have a PC with Windows, an OMC-045-III unit, a SIM card, and appropriate power sources.
Covers: Introduction · Getting Started · Email Configuration · FTP Configuration · Advanced Config Settings · Alarm Handling
Latest Observator manuals
Observator OMC-7006 Buoy User Manual
User Manual 47 pages · 5 MB · ENThis manual provides commissioning, maintenance, and deployment instructions for the Observator OMC-7006 water quality measurement buoy.
OBSERVATOR OMC-406 Temperature Humidity Sensor User Manual
User Manual 6 pages · 439 KB · ENUser manual for the OMC-406 temperature and humidity sensor, covering operation, measurement practices, calibration, and connections.
Observator OMC-116 Ultrasonic Wind Sensor Installation Manual
Installation Guide 11 pages · 468 KB · ENInstallation manual for the Observator OMC-116 ultrasonic wind sensor, covering power requirements, mounting, cabling, and alignment.
OBSERVATOR OMC-045-II & OMC-045-III Data Logger Programming Utility User Manual
User Manual 89 pages · 3 MB · ENUser manual for OMC-Programmer 2010, a utility to configure and program OMC-045-II and OMC-045-III data loggers.
OBSERVATOR OMC-045-II Technical User Manual
User Manual 57 pages · 640 KB · NLUser manual for OBSERVATOR's OMC-045-II data logger with GPRS and GPS, covering installation, sensor connections, and configuration.
Which document do I need?
User Manual
Day-to-day operation, settings and troubleshooting. Start here if the product is already set up.
Installation Guide
Mounting, wiring and first power-up. Read it before the hardware goes in.
Questions answered in Observator manuals
What is the primary purpose of the OMC-7006 buoy?
The OMC-7006 is a buoy meant for water quality measurement.
At what voltage does the backup battery pack automatically take over?
The backup battery pack will automatically take over when the power gets below approx 10.8 V.
What is the humidity measurement range of the OMC-406?
The humidity measurement range is 0 to 100% RH.
From: OBSERVATOR OMC-406 Temperature Humidity Sensor User Manual
How accurate is the temperature measurement?
The temperature accuracy is less than ±0.5°C from -30 to 150°C.
From: OBSERVATOR OMC-406 Temperature Humidity Sensor User Manual
What power supply is required for the OMC-116?
A separate power supply is required: 12-15Vdc 1A when no heating is required, or 24Vdc 10A when sensor heating is required.
From: Observator OMC-116 Ultrasonic Wind Sensor Installation Manual
What is the recommended mounting height for the sensor?
The recommended sensor height is 10m, although an obstacle-free environment is more important.
From: Observator OMC-116 Ultrasonic Wind Sensor Installation Manual
