intersil Manuals (Others)

HI-565A is a fast, 12-bit, current output, digital-to-analog converter produced by Intersil. The monolithic chip includes a precision voltage reference, thin-film R2R ladder, reference control amplifier and twelve high speed bipolar current switches. The Intersil dielectric isolation process provides latch free operation while minimizing stray capacitance and leakage currents, to produce an excellent combination of speed and accuracy. Also, ground currents are minimized to produce a low and constant current through the ground terminal, which reduces error due to code dependent ground currents. HI-565A dice are laser trimmed for a maximum integral nonlinearity error of ±0.5 LSB at 25oC. In addition, the low noise buried zener reference is trimmed both for absolute value and temperature coefficient. Power dissipation is typically 250mW, with ±15V supplies. The HI-565A is offered in both commercial and military grades. See Ordering Information.

File format: PDF Size:250 KB

This document describes the features and characteristics of the HI-303 dual SPDT CMOS analog switch, including break-before-make switching, low and nearly constant ON resistance over the full analog signal range, and low power dissipation. The switch is TTL compatible and has a logic “0” condition with an input less than 0.8V and a logic “1” condition with an input greater than 4V.

File format: PDF Size:303 KB

This document describes the features and characteristics of the HD-6402/883 CMOS Universal Asynchronous Receiver Transmitter (UART), including operating frequency, low power design, programmable word length, stop bits and parity, automatic data formatting and status generation, etc. The HD-6402/883 is designed for interfacing computers or microprocessors to an asynchronous serial data channel and can be used in various applications such as modems, printers, peripherals, and remote data acquisition systems.

File format: PDF Size:142 KB

The HD-4702/883 is a programmable bit rate generator that provides 13 commonly used bit rates, using a 2.4576MHz crystal/input to produce standard frequency output (16 times bit rate), low operating current, and conforms to EIA RS-404 standards.

File format: PDF Size:182 KB

This datasheet introduces the features and characteristics of DG201A and DG202 quad SPST, CMOS analog switches, including input signal range, low rDS(ON), TTL, CMOS compatibility, pull-up resistor, latch-up protection, second source, maximum supply ratings, logic inputs accept negative voltages, and packages.

File format: PDF Size:73 KB

80C88 CMOS 8-/16-Bit Microprocessor is a high performance 8-/16-bit CMOS CPU manufactured using a self-aligned silicon gate CMOS process (Scaled SAJI IV). It has two operating modes, MINimum for small systems and MAXimum for larger applications such as multiprocessing, allowing user configuration to achieve the highest performance level. It is fully compatible with existing NMOS 8088 hardware and Intersil CMOS peripherals. It is fully software compatible with the 80C86, 8086, and 8088 microprocessors, allowing use of existing software in new designs.

File format: PDF Size:541 KB

The 141 TM 80C86 CMOS 16-bit microprocessor is compatible with NMOS 8086 and features a completely static CMOS design, low power operation, and a wide operating temperature range.

File format: PDF Size:737 KB

The HI-5042, HI-5043, HI-5047, HI-5049, HI-5051 CMOS Analog Switches are a family of CMOS analog switches that offer low resistance switching performance for analog voltages up to the supply rails and for signal currents up to 80mA.

File format: PDF Size:429 KB

The HI-201HS is a high-speed analog switch from Intersil. It is manufactured using CMOS technology and has four independently selectable switch channels. It is pin-compatible with the industry standard HI-201 switch. It has a maximum switching time of 50ns, a low ON resistance of 50 ohms, and a wide analog signal range of ±15V. It is suitable for applications that require improved switching performance, especially switching speed, such as high-speed multiplexing, high-frequency analog switching, and sample-and-hold circuits.

File format: PDF Size:660 KB

HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200 240ns, and HI-201 185ns) combined with low power dissipation (15mW at 25oC). Each switch provides low “ON” resistance operation for input signal voltage up to the supply rails and for signal current up to 80mA. Rugged DI construction eliminates latch-up and substrate SCR failure modes. All devices provide break-before-make switching and are TTL and CMOS compatible for maximum application versatility. HI-200/HI-201 are ideal components for use in high frequency analog switching. Typical applications include signal path switching, sample and hold circuit, digital filters, and operational amplifier gain switching networks.

File format: PDF Size:307 KB

The HI-200/883 is a monolithic device comprising two independently selectable SPST switchers which feature fast switching speeds (240ns typical) combined with low power dissipation (15mW typical @ +25°C). Each switch provides low “ON” resistance operation for input signal voltages up to the supply rails and for signal currents up to 25mA continuous. Rugged DI construction eliminates latch-up and substrate SCR failure modes. All devices provide break-before-make switching and are TTL and CMOS compatible for maximum application versatility. HI-200/883 is an ideal component for use in high frequency analog switching. Typical applications include signal path switching, sample and hold circuits, digital filters, and op amp gain switching networks.

File format: PDF Size:278 KB

The DG411/883 series monolithic CMOS analog switches are drop-in replacements for the popular DG211 and DG212 series devices. They include four independent single pole throw (SPST) analog switches, and TTL and CMOS compatible digital inputs. These switches feature lower analog ON-resistance (<35Ω) and faster switch time (tON <175ns) compared to the DG211 or DG212. Charge injection has been reduced, simplifying sample and hold applications. The improvements in the DG411/883 series are made possible by using a high voltage silicon-gate process. An epitaxial layer prevents the latch-up associated with older CMOS technologies. The 44V maximum voltage range permits controlling 40VP-P signals. Power supplies may be single-ended from +5V to +34V, or split from ±5V to ±20V. The four switches are bilateral, equally matched for AC or bidirectional signals. The ON-resistance variation with analog signals is quite low over a ±15V analog input range. This permits independent control of turn-on and turn-off times for SPDT configurations, permitting “break-before-make” or “make-before-break” operations.

File format: PDF Size:215 KB

HA-4900, HA-4902, HA-4905 Precision Quad Comparators offer fast response time, low offset voltage, low offset current and virtually no channel-to-channel crosstalk for applications requiring accurate, high speed, signal level detection

File format: PDF Size:205 KB

The HA-5127/883 is an ultra-low noise, precision operational amplifier that combines precision DC and wideband high-speed characteristics. It utilizes Intersil D.I. technology and advanced processing techniques to achieve low noise precision instrumentation performance with high speed and wideband capability. The amplifier features low VOS, wide gain-bandwidth, high open loop gain, and high CMRR. It operates over a wide supply range and consumes only 120mW of power. The HA-5127/883 is ideal for low-level transducer signal amplifier circuits and can also be used in instrumentation amplifiers, pulse or RF amplifiers, audio preamplifiers, and signal conditioning circuits.

File format: PDF Size:192 KB

The HA-5101/883 is a low noise, high performance operational amplifier. It features an excellent noise voltage density of 4.5nV/√Hz (max) at 1kHz. The unity gain stable HA-5101/883 yields a 10MHz unity gain bandwidth and a 6V/µs slew rate. The HA-5101/883's DC characteristics assure accurate performance. The 3mV (max) offset voltage is externally adjustable and offset voltage drift is just 3µV/°C. Low bias currents (200nA max) reduce input current errors and the high open loop voltage gain of 100kV/V, over temperature, increases the loop gain for low distortion amplification. The HA-5101/883 is ideal for audio applications, especially low-level signal amplifiers such as microphone, tape head and preamplifiers. Additionally, it is well suited for low distortion oscillators, low noise function generators and high Q filters.

File format: PDF Size:1129 KB

HA-5002/883 is a monolithic, wideband, high slew rate, high output current buffer amplifier. It offers 1300V/µs slew rate typically and 110MHz of bandwidth, with ±100mA minimum output current capability and a 3Ω output impedance. It is designed to replace LH0002 with improved reliability and circuit performance.

File format: PDF Size:207 KB

HA-4741 is a quad operational amplifier produced by Broadcom Semiconductor. Its open-loop gain is as high as 3.5MHz, which can be used in applications such as audio amplifiers that require amplification of wideband signals

File format: PDF Size:341 KB

THA-2400/04/05 is a series of four-channel programmable amplifiers providing a level of versatility unsurpassed by any other monolithic operational amplifier.

File format: PDF Size:66 KB

File format: PDF Size:364 KB

HA-5190/5195 are operational amplifiers featuring a combination of speed, precision, and bandwidth. They are capable of delivering 200V/µs slew rate with a settling time of 70ns, making them ideal for output amplifiers for accurate, high-speed D/A converters or the main components in high-speed sample/hold circuits. They are also suitable for pulse and wideband video amplifiers.

File format: PDF Size:268 KB