intersil Manuals (Others)

The HA-5104/883 is a low noise, high performance quad operational amplifier that offers an array of dynamic specifications including 1V/µs slew rate (min), and 8MHz bandwidth (typ). It also features very low noise specifications of 4.3nV/√Hz at 1kHz (typ) or 6nV/√Hz (max).

File format: PDF Size:102 KB

HA-5102/04 series operational amplifiers features low noise, high performance, 8MHz bandwidth, 3V/µs slew rate, 0.5mV offset voltage and 30nA offset current, suitable for audio amplifiers and active filters etc

File format: PDF Size:500 KB

File format: PDF Size:0 KB

This document is about Intersil HA-2544 50MHz, Video Operational Amplifier. It offers high voltage gain (6kV/V) and high phase margin (65 degrees), while maintaining tight gain flatness over the video bandwidth.

File format: PDF Size:773 KB

HA-2539 is a high gain bandwidth product from Intersil, with a very high slew rate and wide bandwidth. The product's gain bandwidth product reaches 600MHz, with a slew rate of 600V/µs, making it ideal for video and RF amplifier designs with a closed loop gain of 10 or greater. The product also has a ±10V swing, excellent AC parameters, and high open loop gain, making it very useful in high speed data acquisition systems.

File format: PDF Size:493 KB

HA-2520/883 is a high-performance operational amplifier from Intersil that offers unsurpassed specifications for slew rate, bandwidth and settling time. It is designed for closed loop gains of 3 or greater without external compensation and provides low offset current and high input impedance. The 100V/µs (min) slew rate and fast settling time make it ideal for pulse amplification and data acquisition designs.

File format: PDF Size:91 KB

The HA-2510/883 is a high performance operational amplifier which sets the standards for maximum slew rate and wide bandwidth operation in moderately powered, internally compensated, monolithic devices. In addition to excellent dynamic characteristics, this dielectrically isolated amplifier also offers low offset current and high input impedance. The ±50V/µs minimum slew rate and fast settling time of the HA-2510/883 are ideally suited for high speed D/A, A/D, and pulse amplification designs. The HA-2510/883’s superior bandwidth and 750kHz minimum full power bandwidth are extremely useful in RF and video applications. To insure compliance with slew rate and transient response specifications, all devices are 100% tested for AC performance characteristics over full temperature limits. To improve signal conditioning accuracy, the HA-2510/883 provides a maximum offset current of 25nA and a minimum input impedance of 50MΩ, both at 25oC, as well as offset voltage adjust capability.

File format: PDF Size:202 KB

File format: PDF Size:0 KB

Intersil's Power Solutions for Intel® Embedded ICs.

File format: PDF Size:477 KB

This document is about Intersil's data converters products, including ADC and DAC

File format: PDF Size:107 KB

This is a product selection guide that introduces the features and characteristics of Intersil automotive IC products.

File format: PDF Size:164 KB

The EL1509 is a medium power differential line driver designed for customer premise line driving in DMT ADSL solutions. This device features a high drive capability of 250mA while consuming only 7.1mA of supply current per amplifier and operating from a single 5V to 12V supply. This driver achieves a typical distortion of less than -85dBc, at 150kHz into a 25Ω load. The EL1509 is available in the industry standard 8 Ld SOIC as well as the thermally-enhanced 8 Ld DFN package. Both are specified for operation over the full -40°C to +85°C temperature range. The EL1509 is ideal for ADSL, SDSL, HDSL2 and VDSL line driving applications.

File format: PDF Size:216 KB

The EL1508 is a differential DSL line driver from Philips designed to drive full rate ADSL signals in both CO and CPE applications at very low power dissipation. Its 450mA high drive capability makes it ideal for both CAP and DMT designs. It contains two wideband, high-voltage, current mode feedback amplifiers with a number of power dissipation reduction features. These drivers achieve an MTPR distortion measurement of better than 70dB, while consuming typically 6mA of total supply current. This supply current can be set using a resistor on the IADJ pin. Two other pins (C0 and C1) can also be used to adjust supply current to one of four pre-set modes (full-IS, 2/3-IS, 1/3-IS, and full power-down). The EL1508 operates on ±5V to ±12V supplies and retains its bandwidth and linearity over the complete supply range. The device is supplied in a thermally-enhanced 20 Ld SOIC (0.300”), a thermally-enhanced 16 Ld SOIC (0.150”), and the small footprint (4x5mm) 24 Ld QFN packages. The EL1508 is specified for operation over the full -40°C to +85°C temperature range.

File format: PDF Size:384 KB

The EL1507 is a medium power differential line driver from Bel Communications. It features a high drive capability of 400mA while consuming only 7.5mA of supply current per amplifier from ±12V supplies. This driver achieves a typical distortion of less than -75dBc, at 1MHz into a 50Ω load. The EL1507 is available in the thermally- enhanced 16 Ld SO package, as well as a 16 Ld QFN package. Both are specified for operation over the full -40°C to +85°C temperature range. The EL1507 has two control pins, C0 and C1. With the selection of C0 and C1, the device can be set into full-IS power, ¾-IS power, ½-IS power, and power down disable modes. The EL1507 maintains excellent distortion and load driving capabilities even in the lowest power settings.

File format: PDF Size:390 KB

The EL1506 is a medium power differential line driver designed for central office and customer premise line driving for DMT ADSL solutions. This device features a high drive capability of 400mA while consuming only 3.5mA of supply current per amplifier from ±12V supplies. This driver achieves a typical distortion of less than -75dBc, at 1MHz into a 50Ω load. The EL1506 is available in the 28-pin HTSSOP and the 24-pin thermally-enhanced SO packages. Both parts are specified for operation over the full -40°C to +85°C temperature range. The EL1506 has an ENABLE pin which can be used to enable and disable the outputs. In most applications, the EL1506 is an upgrade and pin-compatible drop-in replacement for the AD8016.

File format: PDF Size:46 KB

The EL1503A High Power Differential Line Driver is designed for ADSL and HDSL2 applications, providing low distortion and power-saving features.

File format: PDF Size:382 KB

The Intersil X90100 is a non-volatile electronically programmable capacitor with a stable dielectric and low temperature drift coefficient.

File format: PDF Size:183 KB

This document introduces the features of the Intersil X93154 Digitally Controlled Potentiometer (XDCP™), including low noise, low power, 32 taps, stored in non-volatile memory and recalled on subsequent power-up, and can be used in a variety of applications such as bias and gain control, LCD contrast adjustment.

File format: PDF Size:193 KB

File format: PDF Size:0 KB

The X9314 is a single-ended digitally controlled potentiometer from Intersil, which uses a solid-state non-volatile resistive array, and is ideal for digitally controlled resistance trimming. The X9314 is composed of 31 resistive elements. There are tap points accessible to the wiper element between each element and at either end. The position of the wiper element is controlled by the CS, U/D and INC inputs. The position of the wiper can be stored in non-volatile memory and then be recalled upon a subsequent power-up operation. The XDCP can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications including control, parameter adjustments, and signal processing.

File format: PDF Size:197 KB