TEXAS Manuals

This document introduces the features of the DAC856x, DAC816x and DAC756x series products produced by TI company, including relative accuracy, output range, power supply voltage, reference voltage, input data format, working mode, interface, peripheral circuit, etc.

File format: PDF Size:1482 KB

This document introduces the features and characteristics of TI POWER Management Isolated and Non-Isolated Converter Solutions products

File format: PDF Size:2511 KB

The TCM37C14A and TCM37C15A are single-chip PCM combos with programmable gain control. They are designed to perform transmit encoding (A/D conversion) and receive decoding (D/A conversion), as well as the transmit and receive filtering functions required to meet CCITT/(D3/D4) G.711 and G.714 specifications in a PCM system.

File format: PDF Size:351 KB

The CD74HC374 is an octal D-type flip-flop with three-state outputs from Harris, which can drive 15 LSTTL loads. The input interface of the trigger has buffer function, the output interface has three-state output enable control, and can output high impedance state on the output pin.

File format: PDF Size:53 KB

This document describes the features and characteristics of Harris CD74HC283 and CD74HCT283 binary full adders, including adding two 4-bit binary numbers, full internal lookahead, fast ripple carry for economical expansion, operation with both positive and negative logic, wide operating temperature range, balanced propagation delay and transition times, significant power reduction compared to LSTTL logic ICs, etc.

File format: PDF Size:42 KB

The HC138/HC238/HCT138/HCT238 are high speed silicon gate CMOS decoders well suited to memory address decoding or data routing applications. The HC138 and HC238 feature low power consumption typically associated with CMOS circuitry, yet have speeds comparable to low power Schottky TTL logic. The HC/HCT138 series has eight normally high outputs, of which, if the device is enabled, these inputs determine which one will go low or which of the normally low outputs of the HC/HCT238 series will go high. Two active low and one active high enables (E1, E2 and E3) are used to simplify cascading.

File format: PDF Size:36 KB

Introduces two 8-bit serial-in parallel-out shift registers, CD54HC164 and CD54HCT164, with asynchronous reset. They support HC and HCT logic levels and can operate in a wide temperature range of -55°C to 125°C.

File format: PDF Size:39 KB

This document contains preliminary data current as of the publication date and is subject to change without notice. It is a preliminary draft of the TMS320C55x DSP Programmer’s Guide.

File format: PDF Size:1050 KB

This article describes how to extend the common-mode input range of difference amplifiers for use in a wider variety of reduced power-supply applications. By offsetting or dynamically adjusting the common-mode range, the common-mode input range can be increased in reduced power supply applications.

File format: PDF Size:50 KB

MSP430x241x, MSP430x261x mixed-signal microcontrollers are low-power microcontrollers released by Texas Instruments. They are based on the 16-bit RISC architecture, with a working voltage range of 1.8V to 3.6V. They have three-channel internal DMA, 12-bit analog-to-digital converter, 12-bit digital-to-analog converter, 16-bit timer A, 16-bit timer B, four universal serial communication interfaces (USCIs), power supply voltage monitor, brownout detector, bootstrap loader, serial onboard programming and other features.

File format: PDF Size:1820 KB

This document is an introduction to the SN74AVC8T245 datasheet, which mainly introduces the characteristics of the product, including control inputs, maximum data rates, VCC isolation features, self-locking performance, ESD protection, fully configurable dual-rail design, I/O voltage range, etc.

File format: PDF Size:611 KB

This is a 16-bit dual-supply bus transceiver with configurable voltage translation and 3-state outputs.

File format: PDF Size:170 KB

This document describes the features and characteristics of Harris Semiconductor SCHS235, including buffered inputs, propagation delay, ESD protection, SCR-Latchup resistance, low power consumption, balanced propagation delays, and AC type features.

File format: PDF Size:32 KB

The ’HC4040 and ’HCT4040 are 14-stage ripple-carry binary counters. All counter stages are master-slave flip- flops. The state of the stage advances one count on the negative clock transition of each input pulse; a high voltage level on the MR line resets all counters to their zero state. All inputs and outputs are buffered.

File format: PDF Size:53 KB

The 'HC10 and 'HCT10 logic gates utilize silicon gate CMOS technology to achieve operating speeds similar to LSTTL gates with the low power consumption of standard CMOS integrated circuits. All devices have the ability to drive 10 LSTTL loads. The HCT logic family is functionally pin compatible with the standard LS logic family.

File format: PDF Size:138 KB

This document describes the data sheet of Harris Semiconductor SCHS129C, which features unlimited input rise and fall times, exceptionally high noise immunity, wide operating temperature range, etc.

File format: PDF Size:161 KB

This document describes the features and characteristics of the 'HC32 and 'HCT32 products produced by Harris Semiconductor. These products contain four 2-input OR gates and have balanced propagation delay and transition times. They are compatible with LSTTL logic circuits. They are suitable for a wide operating temperature range and have lower power consumption. The document also provides ordering information for the products.

File format: PDF Size:37 KB

The SN74LVC2G02 is a dual 2-input positive-NOR gate designed for 1.65-V to 5.5-V VCC operation. It supports partial-power-down mode operation, and has low power consumption (10-µA maximum ICC), high output drive capability (±24-mA), low output voltage swing (typical VOLP less than 0.8 V), and high electrostatic discharge (ESD) protection (exceeds JESD 22).

File format: PDF Size:169 KB

SN54LV573 and SN74LV573 are octal transparent D-type latches designed for 2.7V to 5.5V VCC operation. These devices feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

File format: PDF Size:182 KB

The document provides a data sheet for Harris Semiconductor SCHS129A, detailing the features, characteristics, and technical specifications of the product.

File format: PDF Size:33 KB