Industrial

This document introduces the features and characteristics of the EVAL-ADF4208EB1 evaluation board, including the required RF and IF VCO and loop filters, the support of 3V or 5V power supplies, and the software control function using Windows 95/98/NT system.

The ADF4157 is a 6 GHz fractional-N frequency synthesizer with a 25-bit fixed modulus, allowing subhertz frequency resolution at 6 GHz. It consists of a low noise digital

The ADF4154 is a fractional-N frequency synthesizer that implements local oscillators in the up conversion and down conversion sections of wireless. It features RF bandwidth 500 MHz to 4 GHz, 2.7 V to 3.3 V power supply, separate VP for extended tuning voltage, etc.

EVAL-ADF411XEB1 is a general purpose PLL evaluation board produced by AD company for evaluating the performance of ADF411X frequency synthesizer. The board contains ADF411X synthesizer interface, reference input interface, power supply interface and RF output interface, and users need to purchase ADF411X synthesizer, VCO and loop filter

This document introduces the features of ADF4118EB1, including self-contained board design, synthesizer for generating WCDMA frequencies, VCO and loop filter.

This is a document about the eval-adf4113eb2 product. The product is a self-contained board that includes a synthesizer, vco, loop filter, and is designed to generate frequencies from 1700mhz to 1800mhz. The product is designed for a 20khz loop bandwidth, and the accompanying software allows complete control of the synthesizer functions from a pc. The product is battery-powered and can be powered by either a 3v or 5v supply. The product has a typical phase noise performance of -86dbc/hz@1khz offset.

This document describes a self-contained board that includes a synthesizer, VCO, and loop filter for generating GSM frequencies (819MHz to 915MHz). It is designed for a 20kHz loop bandwidth. The accompanying software allows complete control of synthesizer functions from a PC. The board can be battery operated with a choice of 3V or 5V supplies. It has a typical phase noise performance of -91dBc/Hz @ 1kHz offset and a typical spurious performance better than -90dBc at 200kHz offset. This document is provided by Analog Devices.

This document describes the features and characteristics of the ADF4112EB1 evaluation board. The evaluation board is a self-contained circuit board that includes a frequency synthesizer and VCO for generating CDMA frequencies. It is designed for a 3kHz loop bandwidth and comes with accompanying software for complete control of the synthesizer functions from a PC. The board can be battery operated with a choice of 3V or 5V supplies and has typical phase noise performance of -81dBc/Hz at 300 Hz offset and better than -81dBc spurious performance at 30kHz offset from the carrier.

The ADF4108 frequency synthesizer is used to implement local oscillators in the up-conversion and down-conversion sections of wireless receivers and transmitters. It features an 8.0 GHz bandwidth, a 3.2 V to 3.6 V power supply, separate charge pump supply, programmable dual modulus prescaler, programmable charge pump currents, programmable antibacklash pulse width, 3-wire serial interface, analog and digital lock detect, and hardware and software power-down mode.

ADE7763 is a single-phase active and apparent energy metering IC that supports IEC 61036/60687, IEC62053-21 and IEC62053-22 standards. It has high accuracy, an on-chip digital integrator, can directly interface to current sensors with di/dt output, a PGA in the current channel allows direct interface to shunts and current transformers, sampled waveform, active and apparent energy, current and voltage rms, positive-only energy accumulation mode, on-chip user programmable threshold, line voltage surge and SAG and PSU supervisory, digital calibration, power, phase and input offset, on-chip temperature sensor (±3°C typical), SPI®-compatible serial interface, programmable frequency pulse output, interrupt request pin (IRQ) and status register.

The ADE7759 is an active energy metering integrated circuit with features such as high accuracy, support for IEC 687/1036 standards, and direct interface with current sensors with di/dt output.

The AD7933/AD7934 are 12-bit and 10-bit, high speed, low power, successive approximation (SAR) ADCs. They operate from a single 2.7 V to 5.25 V power supply and feature throughput rates to 1.5 MSPS. The parts feature 4 analog input channels with a channel sequencer to allow a consecutive sequence of channels to be converted on. These parts can accept either single-ended, fully differential, or pseudo-differential analog inputs.

The AD7923 is a 12-bit, high speed, low power, 4-channel, successive approximation ADC. It features high throughput rate, low power consumption, wide input bandwidth, and flexible power/serial clock speed management.

This document describes the evaluation board for the AD7899 high speed, low power, 14-bit A/D converter. The evaluation board features a full-featured design, suitable for use with the AD7899 Eval-Board controller and standalone use. On-board components include the AD780 +2.5V ultra-high precision bandgap reference and an op-amp for the analog inputs. Interface to this board is through a 96-pin connector.

This is the user manual of Analog Devices' EVAL-AD7898CB evaluation board