Key facts
- Manuals
- 42
- Models
- 11
- Last added
- 2012-08-01
AnaChip models by category
Latest AnaChip manuals
Anachip ATC 2-Wire Serial 16K-bits (2048 x 8) CMOS Electrically Erasable PROM AM24LC16 handbook
The AM24LC16 is a 2-wire serial 16K-bit (2048 x 8) CMOS electrically erasable PROM. It features non-volatile data storage, a 2-wire I2C serial interface, hardware write protection, 16-byte page write mode, and more.
Anachip AM24LC21 Dual Mode 1K-bits (128 x 8) 2-Wire Serial EEPROM (Preliminary) handbook
AM24LC21 is a 128 x 8-bit dual-mode Electrically Erasable PROM manufactured by Anachip Corp. It features single supply with operation down to 2.5V, completely implements DDC1/DDC2 interface for monitor identification, including recovery to DDC1, low power CMOS technology, 1 mA typical active current, 10 uA standby current typical at 5.5V, 2-wire serial interface bus, I2C compatible, 100Khz (2.5V) and 400Khz (5V) compatibility, Self-timed write cycle, Hardware write-protect pin, Page-write buffer, 1,000,000 erase/write cycles, Data retention > 40 years, 8-pin PDIP and SOP packages, Available for extended temperature ranges Commercial (C): 0°C to +70°C Industrial (I): -40°C to +85°C
Anachip AM24LC21B Dual Mode 1K-bits (128 x 8) 2-Wire Serial EEPROM (Preliminary) handbook
Anachip ATC 2-Wire Serial 4K-Bit (512 x 8) CMOS Electrically Erasable PROM AM24LC04 handbook
AM24LC04 is a 2-wire serial 4K-bit CMOS electrically erasable PROM with features including non-volatile data storage, standard voltage and low voltage operation, 16-byte page write mode, self-timed write-cycle, etc.
AnaChip ATS278 handbook
ATS278 is a single chip Hall effect latch with frequency generator (FG) output, which is designed for electronic commutation of two-phase brush-less DC fan applications.
AnaChip ATS276/277 handbook(1)
ATS276/277 are integrated Hall sensors with output drivers, mainly designed for electronic commutation of brush-less DC Fan. This IC internally includes the regulator, protecting diode, Hall plate, amplifier, comparator, and a pair of open-collector outputs (DO, DOB). While the magnetic flux density (B) is larger than operate point (Bop), DO will turn on (low), and meanwhile DOB will turn off (high). Each output is latched until B is lower than release point (Brp), and then DO、DOB transfer each state. For DC fan application, sometimes need to test power reverse connection condition. Internal diode only protects chip-side but not for coil-side. If necessary, add one external diode to block the reverse power.
AnaChip ATS266 handbook
AnaChip AP1601 Data Sheet
The AP1601 is a high efficiency step-up DC/DC converter from Anachip Corp. It can be used with 1 to 4 NiMH battery cells and only requires three external components to deliver a fixed output voltage of 3.3V or 5V. The AP1601 starts up from less than 0.9V input with 1mA load. The Pulse Frequency Modulation scheme provides optimized performance for applications with light output loading and low input voltages. The output ripple and noise are lower compared with the circuits operating in PSM mode. The PFM control circuit operating in 100KHz (max.) switching rate results in smaller passive components. The space saving MSOP packages make the AP1601 an ideal choice of DC/DC converter for space conscious applications, like pagers, electronic cameras, and wireless microphones.
ANACHIP AF9412N DATA SHEET
Anachip AF9412N N-Channel 30-V (D-S) MOSFET is a low-power N-channel MOSFET with a rated voltage of 30V. Typical applications include PWM DC-DC converters, power management in portable and battery-powered products such as computers, printers, battery chargers, telecommunication power systems, and telephone power systems.
ANACHIP AP1307 DATA SHEET
The AP1307 fan motor predriver is suited for two-coil brush-less DC fan. It is compatible with a Hall element and has an operating voltage of 4V to 28V. Other features include lock shutdown and automatic restart, rotation detection output, maximum output current of 70mA, and an operating temperature range of -30ºC to +85ºC.
ANACHIP AP1184 DATA SHEET
AP1184 is a 4A low dropout regulator produced by Anachip. It has the characteristics of adjustable and fixed output voltage. The adjustable output voltage range is 1.5V-5.0V, and the output current can reach 4A. It has good anti-interference performance and is suitable for applications that require 2.8V or lower voltage.
Anachip AH285 DATA SHEET
AH285 is an integrated fan motor controller with Hall sensor's capability, produced by Anachip. It contains two complementary open-drain transistors as motor coil drivers, automatic lock current shutdown, and recovery protections. The output current is 500mA and the working voltage is 3.8V~20V.
AnaChip AD6315 handbook
AD6315 is a VFD (Vacuum Fluorescent Display or fluorescent Indicator Panel) driver that is driven on a 1/4- to 1/12- duty factor. It consists of 16 segments and 4 grids output lines, 8 segments / grid output driving lines, a display memory, a control circuit, and a key scan circuit. Serial data is input to the AD6315 through a 3-wire serial interface. This VFD driver is ideal as a peripheral device for a single-chip microcomputer.
AnaChip AD6312 handbook
The AD6312 is a VFD (Vacuum Fluorescent Display) controller/driver with a 1/4- to 1/11 duty factor. It features a 4-pin serial interface, key scanning, programming display modes, programming dimming step, high-voltage output, 4 channels LED ports, 4-pin general-purpose input port, built-in oscillator, and no external resistor necessary for driver outputs.
AnaChip AD6311 handbook
The AD6311 is a VFD (Vacuum Fluorescent Display) controller/driver that is driven on a 1/8- to 1/16 duty factor (include key scan). It consists of 12 segment/key scan output lines, 8 grid output lines, 8 segment/grid output drive lines, a display memory, a control circuit, and a key scan circuit. Serial data is input to the AD6311 through a four-line serial interface.