ST Manuals

The VNL5050N3-E / VNL5050S5-E OMNIFET III fully protected low-side driver is a low-side driver launched by STMicroelectronics. It has a maximum current of 19A, ESD protection, overvoltage clamp, thermal shutdown, current and power limitation, ultra-low standby current, ultra-low electromagnetic susceptibility and compliance with the European Union 2002/95/EC directive.

The VN5E010AH is a single-channel high-side driver manufactured in the ST proprietary VIPower M0-5 technology and housed in the tiny HPAK package. It is designed to drive 12 V automotive grounded loads delivering protection, diagnostics and easy 3 V and 5 V CMOS compatible interface with any microcontroller.

The VN5E016AH-E is a single channel high-side driver manufactured in the ST proprietary VIPower™ M0-5 technology and housed in the tiny HPak package. It is designed to drive 12 V automotive grounded loads delivering protection, diagnostics and easy 3 V and 5 V CMOS compatible interface with any microcontroller.

The VNH5050A-E is a full bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high-side driver and two low-side switches. All switches are designed using STMicroelectronics' VIPower M0 technology that allows to efficiently integrate on the same die a true Power MOSFET with an intelligent signal/protection circuitry. The device features an output current of 30A, 3V CMOS compatible inputs, undervoltage and overvoltage shutdown, overvoltage clamp, thermal shutdown, cross-conduction protection, current and power limitation, very low standby power consumption, PWM operation up to 20KHz, protection against loss of ground and loss of VCC, current sense output proportional to motor current, output protected against short to ground and short to VCC, etc.

TDA7541B is a high performance tuner circuit with stereo decoder for AM/FM car radio. It contains a mixer, IF amplifier, demodulator for AM and FM, stereo decoder, quality detection, ISS filter and PLL synthesizer with IF counter on a single chip.

The L99MD02 is a 6-channel half-bridge driver for automotive applications. It can drive 3 DC motors simultaneously or up to 5 DC motors in series. It has an integrated 24-bit standard serial peripheral interface (SPI) to control all outputs and provide diagnostic information: normal operation, open-load in on-state, overcurrent, temperature warning and overtemperature.

The VN5772AK-E is a quad smart power solid-state relay for complete H-bridge configurations. The product features active power limitation on the high-side switches to manage inrush current, very low standby current, very low electromagnetic susceptibility, and compliance with European directive 2002/95/EC.

SPC560P34L1, SPC560P34L3, SPC560P40L1, SPC560P40L3 are 32-bit Power Architecture® based MCUs with 320 KB Flash memory and 20 KB RAM for automotive chassis and safety applications

The document introduces the features of the L9953LXP door motor driver, including 3 half bridge drivers, 2 configurable high side drivers, 1 full bridge driver, 1 high side driver, programmable soft start function, low standby current, short circuit protection, current monitoring output, over temperature protection, open load diagnosis, overload diagnosis, separate half bridge drivers, PWM control, charge pump output, etc.

L9954LXP is a microcontroller driven multifunctional door actuator driver for automotive applications. Up to two DC motors and three grounded resistive loads can be driven with three half bridges and three high-side drivers.

The VND5E025BK-E is a double channel high- side driver manufactured in the ST proprietary VIPower™ M0-5 technology and housed in the tiny PowerSSO-24 package. It is designed to drive 12V automotive grounded loads delivering protection, diagnostics and easy 3V and 5V CMOS compatible interface with any microcontroller.

This document provides preliminary information on a new product currently in development or undergoing evaluation. The product is a 32-bit MCU family built on the Power Architecture® for automotive body electronics applications. It features a high-performance 48 MHz e200z0h CPU, variable length encoding (VLE), up to 256 KB Code Flash with ECC, up to 64 KB Data Flash with ECC, up to 16 KB SRAM with ECC, 16-channel eDMA, GPIOs, timer units, time-triggered I/Os, analog-to-digital converter (ADC), dedicated diagnostic module for lighting, communications interfaces, and clock generation.

The L99PM62XP is a power management IC with LIN and high speed CAN features, including ultra low quiescent current, programmable reset generator, configurable window watchdog, and fail safe output.

The VNL5160N3-E and VNL5160S5-E are monolithic devices, made using STMicroelectronics® VIPower® Technology, intended for driving resistive or inductive loads with one side connected to the battery.