ST Manuals

The SPC560B40x, SPC560B50x, SPC560C40x and SPC560C50x are a 32-bit MCU family based on the Power Architecture® for automotive body electronics applications.

The VND5E025AK-E is a double channel high-side driver manufactured in the ST proprietary VIPower M0-5 technology and housed in the tiny PowerSSO-24 package. The VND5E025AK-E is designed to drive 12 V automotive grounded loads delivering protection, diagnostics and an easy 3 V and 5 V CMOS compatible interface with any microcontroller. The device integrates analog current sense, programmable current limiting, short circuit protection, open load detection and thermal shutdown functions.

This document introduces the features and characteristics of VND5E050AJ-E and VND5E050AK-E. These two products are low-power dual channel high side drivers manufactured in the ST proprietary VIPower M0-5 technology and housed in the tiny PowerSSO-12 and PowerSSO-24 packages. These two products can drive 12V automotive grounded loads delivering protection, diagnostics and easy 3V and 5V supply.

VN5E050AJ-E is a single channel high-side driver manufactured in the ST proprietary VIPower M0-5 technology and housed in the tiny PowerSSO-12 package. The VN5E050AJ-E is designed to drive 12V automotive grounded loads delivering protection, diagnostics and easy 3V and 5V CMOS compatible interface with any microcontroller. The device integrates advanced protection features and diagnostics, including short circuit protection, over current protection, over temperature protection, under voltage protection, loss of ground protection, output short circuit protection, current detection failure protection, output shutdown protection, and current overcurrent protection, and supports 3.0V CMOS compatible inputs.

VND5E050J-E and VND5E050K-E are double channel high-side drivers for automotive applications, featuring inrush current active management by power limitation, very low standby current, 3.0V CMOS compatible inputs, optimized electromagnetic emissions, and very low electromagnetic susceptibility.

The VNQ5E160K-E is a quad channel high-side driver designed for automotive applications. It features inrush current active management by power limitation, very low standby current, 3.0V CMOS compatible inputs, optimized electromagnetic emissions, very low electromagnetic susceptibility, and compliance with the 2002/95/EC European directive.

The L9332 is a monolithic integrated quad low side driver realized in an advanced Multipower BCD mixed technology. The device is intended to drive valves in automotive environment. The inputs are µP compatible. Particular care has been taken to protect the device against failures, to avoid electromagnetic interferences and to offer extensive real time diagnostic.

The L5957 is a multifunction voltage regulator for car radio. It features four outputs: 8.5 V @ 500 mA, 5 V @ 300 mA permanent, 5 V @ 800 mA, and 3.3 V @ 800 mA. Additionally, it includes a 2A high side driver, reset function, ignition comparator, load dump protection, thermal shutdown, and overcurrent limitation.

TDA7563A is a multifunctional quad power amplifier with built-in diagnostics feature. It features multipower BCD technology, MOSFET output power stage, DMOS power output, and high efficiency. It has high output power capability and supports I2C bus digital diagnostics. It also has full fault protection and DC offset detection.

The L9954 and L9954XP are microcontroller driven, multifunctional door actuator drivers for automotive applications. Up to two DC motors and three grounded resistive loads can be driven with three half bridges and three highside drivers. The integrated standard serial peripheral interface (SPI) controls all operation modes (forward, reverse, brake and high impedance). All diagnostic information is available via the SPI.

The L9953 is a microcontroller-driven multifunctional door actuator driver for automotive applications. It features one full bridge, three half bridges and three high side drivers, which can drive up to three DC motors and three grounded resistive loads. The integrated standard serial peripheral interface (SPI) controls all operation modes (forward, reverse, brake and high impedance). All diagnostic information is available via SPI.

The L9758 is a multiple output voltage regulator utilizing linear, switchmode (buck and boost) and tracking regulators to support high end automotive microcontrollers used in powertrain applications. The L9758 provides two standby power regulators as well as controllable LDO regulators. The L9758 has power on reset functionality and controlled slew rate of the VDD5, VDDL and VCORE. PowerSO-36

TDA7388A is a new technology class AB audio power amplifier in Flexiwatt27 package designed for high end car radio applications.

TDA7388 is a 4 x 45 W quad bridge car radio amplifier produced by ST company. It has the advantages of high output power, low distortion, low noise, standby function, mute function, automute and low external component count.