ON Semiconductor manuals, page 16
ON Semiconductor MC14553B Data Sheet
MC14553B/D 3-digit BCD counter
ON Semiconductor MUN5111T1 Series handbook
The MUN5111T1 series of bias resistor transistors is a new family of digital transistors designed to replace a single device and its external resistor bias network. The device is housed in the SC-70/SOT-323 package which is designed for low power surface mount applications.
ON Semiconductor MC34063A MC33063A handbook
MC34063A/D is a monolithic control circuit for DC-to-DC converters. It includes internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch.
ON Semiconductor NTLJS3113P handbook
ON Semiconductor NCP1450A handbook
The NCP1450A is a PWM step-up DC-DC switching controller produced by Semiconductor Components Industries, LLC. It is designed to power portable equipment from one or two cells battery packs. It features high efficiency, low start-up voltage, wide operating voltage range, etc.
ON Semiconductor NCP1030 NCP1031 handbook
NCP1030 and NCP1031 are monolithic switching regulators with on-chip Power Switch and Startup Circuits.
ON Semiconductor MMSZ5221ET1 Series handbook
The document introduces the MMSZ5221ET1 series preferred device Zener voltage regulators 500 mW SOD−123 surface mount
ON Semiconductor MCR100 Series handbook
MCR100 series SCRs are PNPN devices designed for high-volume, line-powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits. Supplied in an inexpensive plastic TO-226AA package which is readily adaptable for use in automatic insertion equipment.
ON Semiconductor MC33375 Series handbook
The MC33375 series is a micro-power low dropout voltage regulator with a very low quiescent current and the ability to supply output currents up to 300mA.
ON Semiconductor MC14066B handbook
The MC14066B/D is a quad bilateral switch capable of controlling either digital or analog signals. It is useful in signal gating, chopper, modulator, demodulator and CMOS logic implementation. It is designed to be pin–for–pin compatible with the MC14016B, but has much lower ON resistance. Input voltage swings as large as the full supply voltage can be controlled via each independent control input.
ON Semiconductor MBR140SFT1 handbook
MBR140SFT1/D MBR140SFT1 Surface Mount Schottky Power Rectifier Plastic SOD-123 Package
ON Semiconductor NTLTD7900ZR2 handbook
This document introduces the NTLTD7900ZR2 Power MOSFET, which is a logic level N-channel Micro8 Leadless EZFETs™ power MOSFET with monolithic back-to-back Zener diode protection. This MOSFET features ultra low RDS(on) and true logic level performance. It is designed for low voltage, high speed switching applications that require high power efficiency and extended battery life. Typical applications include DC-DC converters, and power management in portable and battery powered products such as computers, printers, cellular and cordless phones.
ON SEMICONDUCTOR NCP302 NCP303 handbook
The NCP302 and NCP303 series are second generation ultra-low current voltage detectors that contain a programmable time delay generator. These devices are specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is paramount. Each series features a highly accurate undervoltage detector with hysteresis and an externally programmable time delay generator. This combination of features prevents erratic system reset operation. The NCP302 series consists of complementary output devices that are available with either an active high or active low reset. The NCP303 series has an open drain N-Channel output with an active low reset output.
ON Semiconductor NCP1800 handbook
ON Semiconductor SN74LS365A SN74LS367A SN74LS368A DATA SHEET
These devices are high speed hex buffers with 3-state outputs. They are organized as single 6-bit or 2-bit/4-bit, with inverting or non-inverting data (D) paths. The outputs are designed to drive 15 TTL Unit Loads or 60 Low Power Schottky loads when the Enable (E) is LOW. When the Output Enable (E) is HIGH, the outputs are forced to a high impedance “off” state. If the outputs of the 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so there is no overlap.