Maxim manuals, page 48
MAXIM MAX3314 Manual
The MAX3314 is a ±5V powered EIA/TIA-232-compatible interface. It has one transmitter and one receiver in a flow-through architecture. The transmitter has a low-dropout output stage providing minimum RS-232-compatible ±3.7V output levels while driving 3kΩ and 1000pf at 460kbps. Both +5V and -5V are supplied externally. The MAX3314 has a SHDN function that reduces supply current to 1µA. The transmitter is disabled and put into 3-state mode while the receiver remains active. The MAX3314 is available in 8-pin SOT23, µMAX and SO packages.
MAXIM MAX3228/3229 Manual
The MAX3228/MAX3229 are +2.5V to +5.5V powered EIA/TIA-232 and V.28/V.24 communications interfaces with low power requirements, and high data-rate capa- bilities, in a chip-scale package (UCSP™). The MAX3228/MAX3229 achieve a 1µA supply current with Maxim’s AutoShutdown™ feature. They save power without changes to existing BIOS or operating systems by entering low-power shutdown mode when the RS-232 cable is disconnected, or when the trans- mitters of the connected peripherals are off. The transceivers have a proprietary low-dropout trans- mitter output stage, delivering RS-232 compliant perfor- mance from a +3.1V to +5.5V supply, and RS-232 compatible performance with a supply voltage as low as +2.5V. The dual charge pump requires only four small 0.1µF capacitors for operation from a +3.0V sup- ply. Each device is guaranteed to run at data rates of 250kbps while maintaining RS-232 output levels. The MAX3228/MAX3229 offer a separate power-supply input for the logic interface, allowing configurable logic levels on the receiver outputs and transmitter inputs. Operating over a +1.65V to VCC range, VL provides the MAX3228/MAX3229 compatibility with multiple logic families. The MAX3229 contains one receiver and one transmit- ter. The MAX3228 contains two receivers and two transmitters. The MAX3228/MAX3229 are available in tiny chip-scale packaging and are specified across the extended industrial temperature range of -40°C to +85°C.
MAXIM MAX3228E/322EAE/3229E/MAX3229AE Manual
The MAX3228E/AE and MAX3229E/AE are +2.5V to +5.5V powered EIA/TIA-232 and V.28/V.24 communications interfaces with low power requirements, high data-rate capabilities, and enhanced electrostatic discharge (ESD) protection, in a chip-scale package (UCSP™) and WLP Package. All transmitter outputs and receiver inputs are protected to ±15kV using IEC 1000-4-2 Air-Gap Discharge, ±8kV using IEC 1000-4-2 Contact Discharge, and ±15kV using the Human Body Model. The MAX3228E/AE and MAX3229E/AE achieve a 1µA supply current with Maxim’s AutoShutdown™ feature. They save power without changes to existing BIOS or operating systems by entering low-power shutdown mode when the RS-232 cable is disconnected, or when the transmitters of the connected peripherals are off. The transceivers have a proprietary low-dropout transmitter output stage, delivering RS-232 compliant performance from a +3.1V to +5.5V supply, and RS-232 compatible performance with a supply voltage as low as +2.5V. The dual charge pump requires only four small 0.1µF capacitors for operation from a +3.0V sup- ply. Each device is guaranteed to run at data rates of 250kbps while maintaining RS-232 output levels. The MAX3228E/AE and MAX3229E/AE offer a separate power-supply input for the logic interface, allowing configurable logic levels on the receiver outputs and transmitter inputs. Operating over a +1.65V to VCC range, VL provides the MAX3228E/AE and MAX3229E/AE compatibility with multiple l...
MAXIM MAX3250 Manual(1)
The MAX3250 is a 3.0V to 5.5V powered, ±50V isolated EIA/TIA-232 and V.28/V.24 communications interface with high data-rate capabilities. The MAX3250 is a dual die part that operates with up to ±50V difference between the RS-232 side and the logic side (ISOCOM to GND). This makes the device ideal for operation in noisy conditions with high common-mode voltages. This feature prevents damage to the device if RS-232 lines are inadvertently short-circuited to a +24V or ±48V power bus. The MAX3250 is powered by a single 3V to 5.5V supply on the logic side. Power is transferred from the logic side to the isolated side by ±100V external capacitors. The MAX3250 has two receivers (Rx) and two drivers (Tx) and is guaranteed to run at data rates of 250kbps while maintaining RS-232 output levels. The trans- ceivers have a proprietary low-dropout transmitter out- put stage, delivering true RS-232 performance from a 3V to 5.5V supply with a dual charge pump. The device features a FAULT open-drain output to signal an exces- sive isolated-side voltage condition on any of the RS- 232 inputs. This output can drive an alarm LED or can be monitored by the processor to prevent operation under these conditions. The receiver outputs are high impedance in shutdown, allowing multiple interfaces (IrDA, RS-232, RS-485) to be connected to the same UART. The MAX3250 is available in a space-saving 28-pin SSOP package. Applications Industrial Control Programmable Logic Controller Point-to-Point Communication Data Acquisition
MAXIM MAX3322E/3323E Manual
The MAX3322E/MAX3323E 3.0V to 5.5V powered EIA/TIA-232 and V.28/V.24 communications interfaces are designed for multidrop applications with low power requirements, high data-rate capabilities, and enhanced electrostatic discharge (ESD) protection.
MAXIM MAX3222E/MAX3232E/MAX3237E/MAX3241E /MAX3246E handbook
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/MAX3246E are +3.0V-powered EIA/TIA-232 and V.28/V.24 communication interface devices that offer low power consumption, high data rate capabilities, and enhanced electrostatic discharge (ESD) protection.
MAXIM MAX3230E/MAX3230AE/MAX3231E/MAX3231AE handbook
MAX3230E/AE and MAX3231E/AE are +2.5V to +5.5V powered EIA/TIA-232 and V.28/V.24 communications interfaces with low power requirements, high data-rate capabilities, and enhanced electrostatic discharge (ESD) protection, in a chip-scale package (UCSP™) and WLP package.
MAXIM MAX13234E-MAX13237E Manual
The MAX13234E–MAX13237E are +3V to +5.5V powered EIA/TIA-232 and V.28/V.24 communications interfaces with high data-rate capabilities (up to 3Mbps), a flexible logic voltage interface, and enhanced electrostatic discharge (ESD) protection. All receiver inputs and transmitter outputs are protected to ±15kV IEC 61000–4-2 Air Gap Discharge, ±8kV IEC 61000-4-2 Contact Discharge, and ±15kV Human Body Model. The MAX13234E/MAX13235E have two receivers and two transmitters, while the MAX13236E/MAX13237E have a single receiver and transmitter. The transmitters have a low-dropout transmitter output stage, delivering true RS-232 performance from a +3V to +5.5V supply based on a dual charge pump. The charge pump requires only four small 0.1µF capacitors for operation from a +3.3V supply. All devices achieve a 1µA supply current using Maxim’s AutoShutdown Plus™ feature. These devices automatically enter a low-power shutdown mode when the RS-232 cable is disconnected or the devices driving the transmitter and receiver inputs are inactive for more than 30s. The MAX13234E–MAX13237E are available in space-saving TQFN and TSSOP packages and operate over the -40°C to +85°C extended temperature range.
MAXIM MAX869L Manual
The MAX869L is a P-channel load switch with accurate user-set current limit and low on-resistance. It is designed to protect the power source from shorts and surges by limiting current and preventing the system supply from being pulled low. The input voltage range is 2.7V to 5.5V. The MAX869L features a 2A, 45mΩ switch controlled by a logic signal. The current limit can be set from 400mA to 2.4A with ±21% accuracy using a single resistor. The device has a low quiescent supply current of 12µA, which reduces to a maximum of 2µA in shutdown. It also includes thermal shutdown protection and a logic signal output pin (FAULT) for indicating overcurrent or overtemperature conditions. For other devices in this family, please refer to the Selector Guide.
MAXIM MAX893L Manual
MAX893L is a high-side load switch from Maxim Integrated. It operates with input voltages from +2.7V to +5.5V and can continuously output up to 1.2A of current. The short-circuit current is limited to 1.8A. The switch features internal current-limiting circuitry and thermal overload protection.
MAXIM MAX1607 Manual
MAX1607 is a precise preset current-limited switch for USB applications. The switch has low quiescent supply current and standby current to conserve battery power in portable applications.
MAXIM MAX1823/MAX1823A/MAX1823B/MAX1823H handbook
The MAX1823 is a dual, current-limited switch with autoreset specifically made for USB applications. The autoreset feature latches the switch off if the output is shorted, saving system power. The switch reactivates when the short circuit is removed. Each channel is guar- anteed to supply 720mA and meet USB specifications. Low quiescent supply current (50µA) and standby current (3µA) conserve battery power in portable applications. The MAX1823 has multiple safety features to ensure that the USB port is protected. Built-in thermal-overload protection limits power dissipation and junction temper- ature. Accurate internal current-limiting circuitry pro- tects the input supply against both overload and short-circuit conditions. Independent fault signals (FAULTA and FAULTB) notify the microprocessor (µP) when a thermal-overload, current-limit, undervoltage- lockout (UVLO), or short-circuit fault occurs. A 20ms fault-blanking feature ignores momentary faults, such as those caused when hot swapping a capacitive load, preventing false alarms to the host system. The MAX1823A/MAX1823B also block reverse current (cur- rent from OUT_ to IN_) while in shutdown. The MAX1823 is available in a space-saving 10-pin µMAX package. The MAX1823/MAX1823A are enabled with an active-low signal, and the MAX1823B/MAX1823H are enabled with an active-high signal. For a single ver- sion of this device, refer to the MAX1946 data sheet. For a triple version, refer to the MAX1940 data sheet.
MAXIM MAX1838 Manual
The MAX1838 is a dual, current-limited USB switch with auxiliary input supply. Each switch meets all IEC specifications for USB ports and is guaranteed to supply 500mA from either of two input supplies. A control pin selects the power source from either the main or auxiliary supply. The MAX1838 has multiple protection features, including independent thermal-shutdown on each channel to limit junction temperature in case of a prolonged short or overload condition. The device has accurate internal current-limit and reverse-current protection to safeguard the input supply against overload. When powered from the auxiliary supply, the current limit on each channel is set independently with an external resistor. An autoreset feature latches the switch off if the output is shorted, thereby saving system power. When the short is removed, the switch automatically turns back on. Independent fault signals (FAULTA and FAULTB) notify the microprocessor (µP) that the internal current limit has been reached. A 20ms fault-blanking feature prevents the MAX1838 from issuing false alarms to the host during power-up or when hot-swapping into a capacitive load. The MAX1838 is available in a space-saving 16-pin QSOP. For other USB current-limited switches, refer to the MAX1693, MAX1694, MAX1812, and MAX1823.
MAXIM MAX1922 Manual
The MAX1922 is a 1A current-limited switch with built-in fault blanking that provides an accurate, preset 1.4A to 2.1A current limit, making it ideal for dual USB applications. Its low quiescent supply current (16µA) and standby current (1µA) conserve battery power in portable applications. The MAX1922 operates with inputs from 2.7V to 5.5V, making it ideal for both 3V and 5V systems. An overcurrent signal (OC) notifies the microprocessor that the internal current limit has been reached. A 10ms overcurrent-blanking feature allows momentary faults (such as those caused when hot-swapping into a capacitive load) to be ignored, thus preventing false alarms to the host system. This blanking also prevents an OC signal from being issued when the device is powering up. The MAX1922 has several safety features to ensure that the USB port is protected. Built-in thermal-overload protection limits power dissipation and junction temperature. The device also has accurate internal current-limiting circuitry to protect the input supply against overload. The MAX1922 is offered in a space-saving 8-pin SO package and a 10-pin TDFN package.
MAXIM MAX1931 Manual
MAX1931 is a 60 mΩ switch with an accurate preset current limit of 0.64A to 1.06A, making it ideally suited for USB applications.