TEXAS Manuals

TPS6300x is a high-efficiency single inductor buck-boost converter with up to 1200mA output current and a working voltage range of 1.8V~5.5V.

The CC1100 is a low cost true single chip UHF transceiver designed for very low power wireless applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency bands at 315, 433, 868 and 915 MHz, but can easily be programmed for operation at other frequencies in the 300-348 MHz, 400-464 MHz and 800-928 MHz bands. The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 500 kbps. The communication range can be increased by enabling a Forward Error Correction option, which is integrated in the modem. CC1100 provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication and wake-on-radio. The main operating parameters and the 64-byte transmit/receive FIFOs of CC1100 can be controlled via an SPI interface. In a typical system, the CC1100 will be used together with a m

This document introduces TPS61010, TPS61011, TPS61012, TPS61013, TPS61014, TPS61015, TPS61016 these high efficiency, 1-cell and 2-cell boost converters. These devices use an integrated synchronous rectifier for highest power conversion efficiency (>95%), support output current of 200 mA with a supply voltage of only 0.9 V. The converter starts up into a full load with a supply voltage of only 0.9 V and stays in operation with supply voltages down to 0.8 V. Since it uses a built-in synchronous rectifier, no external Schottky diode is required, thus the system efficiency is improved. The current through the switch is limited to a maximum of 50 µA.

SLVS485 is a nonsynchronous step-down controller that is ideally suited for systems powered from a 5-V or 3.3-V bus or for applications powered from a 1-cell Li-Ion battery or from a 2- to 4-cell NiCd, NiMH, or alkaline battery. This controller uses a minimum on time, minimum off time control scheme and consumes only 20-µA quiescent current to achieve highest efficiency over a wide load current range. The TPS6420x is suitable for applications such as USB powered peripherals, organizers, PDAs, handheld PCs, low power DSP supply, digital cameras, hard disk drives, and portable audio players.

The ADS1602 is a high performance analog-to-digital converter with high sampling rate, low power consumption and outstanding anti-noise performance. The product is suitable for various applications such as sonar, vibration analysis and data acquisition.

The document describes the features and characteristics of the TPS6120x series products, including low input voltage synchronous boost converter, power save mode for improved efficiency at low output power, over 90% efficiency, overtemperature protection, automatic transition between boost mode and down conversion mode, etc.

This document describes the features and characteristics of high-speed differential receivers such as SN65LVDT32B, SN65LVDS32B, SN65LVDT3486B, SN65LVDS3486B, SN65LVDT9637B, and SN65LVDS9637B. These products comply with the ANSI EIA/TIA-644 standard, support signaling rates up to 400 Mbps, operate with a single 3.3V supply, have a common-mode input voltage range of -2V to 4.4V, differential input thresholds less than 50 mV with 50 mV of hysteresis over the entire common-mode input voltage range, integrated 110-Ω line termination resistors, propagation delay times of 4 ns (typical), active fail-safe feature ensuring a high-level output with no input, bus-pin ESD protection exceeding 15 kV HBM, inputs remaining high-impedance on power down, recommended maximum parallel rate of 200 M-Transfer/s. These products are available in a small-outline package with 1.27 mm terminal spacing.

The THS415x is a family of high performance fully differential input/differential output devices fabricated using Texas Instruments' state-of-the-art BiComI complementary bipolar process. The THS415x is made of a true fully-differential signal path from input to output. This design leads to high performance and wide power supply range, which offers significant advantages in many applications.

The TPS40075 is a mid-range input synchronous buck controller with features such as fixed-frequency voltage-mode control and predictive gate drive, which can maximize efficiency.

The ADS831 is an 8-bit, 80MHz sampling rate analog-to-digital converter. It has high SNR, internal or external reference options, single-ended or differential analog input, programmable input range, low power, low DNL, and single +5V supply, suitable for medical imaging, video digitization, computer scanners, communications and disk drive control applications.

The ADS5521 is a high-performance, 12-bit, 105MSPS analog-to-digital converter (ADC). ADS5521 provides a complete converter solution, including a high-bandwidth linear sample-and-hold stage (S&H) and internal reference. Designed for applications demanding the highest speed and highest dynamic range.

The THS3091 and THS3095 are high-voltage, low-distortion, high-speed, current-feedback operational amplifiers. They are designed to operate over a wide supply range of ±5V to ±15V for applications requiring large, linear output signals such as Pin, Power FET, and VDSL line drivers. The THS3095 features a power-down pin (PD) that puts the amplifier in low power standby mode, and lowers the quiescent current from 9.5mA to 500µA.

the tps54240 is a ti-launched 3.5v to 42v step-down converter with an integrated high side mosfet, external clock synchronization, low power mode, and can be used in 12v and 24v industrial and commercial low power systems.