MICROCHIP Manuals

The MCP3550/1/3 are 22-bit ADC chips from Microchip Technology Inc. The chip has automatic internal offset and gain calibration function, the output noise is as low as 2.5 µVRMS, the effective resolution is 21.9 bits, the typical offset error is 3 µV, the typical full-scale error is 2 ppm, the maximum INL error is 6 ppm, the total unadjusted error is less than 10 ppm, and it supports no digital filter settling time and single-command conversion through 3-wire SPI interface. In addition, the chip also has ultra-low conversion current (MCP3550/1): the typical value is 100 µA under 2.7V power supply voltage and the typical value is 120 µA under 5.0V power supply voltage. The chip supports VSS to VDD common voltage range differential input, supports 2.7V to 5.5V single-supply operation, and the working temperature range is -40°C to +125°C. MCP3550/1/3 chips are suitable for applications such as weighing scales, direct temperature measurement, 6-digit DVMs, instrumentation, data acquisition and strain gauge measurement.

This document describes the features and characteristics of the 24AA04/24LC04B devices from Microchip Technology Inc. The device is a 4 Kbit Electrically Erasable PROM, designed for low-voltage operation down to 1.8V, with standby and active currents of only 1 μA and 1 mA, respectively. It has two blocks of 256 x 8-bit memory and uses a 2-wire serial interface. The device supports page write capability for up to 16 bytes of data. It is available in various package options and temperature ranges.

This data sheet describes the features of a 14-pin flash-based, 8-bit CMOS microcontroller with nanoWatt technology.

TCN75A is a digital temperature sensor from Microchip Technology Inc. with ±1°C (typ.) accuracy, it can convert temperature from -40°C to +125°C to digital data. It supports user-defined resolution, power-saving mode, single conversion, alert output and hysteresis limits.

The MCP6541/2/3/4 family of comparators is a low power, single-supply, greater than rail-to-rail input operation comparator with push-pull (CMOS/TTL-compatible) outputs capable of driving heavy DC or capacitive loads.

Technical specifications manual for 8/14-Pin, 8-Bit Flash Microcontroller released by Microchip Technology Inc., including information on product features, usage instructions, application scenarios, etc.

DS41250F is a 28/40/44/64-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt Technology data sheet published by Microchip

MCP4017/18/19 are programmable resistor products produced by Microchip Technology Inc., with four resistance values of 5kΩ, 10kΩ, 50kΩ and 100kΩ, 7-bit resolution, low temperature drift and low power consumption.

The MCP1804 is a CMOS low dropout linear regulator that can operate from a 2.0V to 28.0V input voltage range and delivers up to 150mA of output current with only 50µA of input current. The device supports output voltages from 1.8V to 18.0V in 0.1V increments, with an output voltage accuracy of ±2%.

MCP4725 is a 12-bit single channel, low power, high accuracy, digital to analog converter (DAC) with non-volatile memory (EEPROM) from Microchip Technology Inc.

MCP9800/1/2/3 is a family of digital temperature sensors from Microchip Technology Inc. that converts temperatures between -55°C and +125°C to a digital word. The products provide an accuracy of ±1°C (max.) from -10°C to +85°C and can be configured to operate in a variety of modes, including user-selectable 9-12 bit temperature measurement resolution, power-saving Shutdown and One-shot (single conversion on command while in the Shutdown) modes. Typical applications include personal computers and servers, hard disk drives and other PC peripherals, entertainment systems, office equipment, data communication equipment, mobile phones, and general-purpose temperature monitoring.

The MCP3004/3008 is a 10-bit analog-to-digital converter from Microchip Technology Inc. with on-board sample and hold circuitry. It features 4 (MCP3004) or 8 (MCP3008) input channels, which can be programmed as single-ended or pseudo-differential pairs. The devices support SPI serial interface and operate on a single supply voltage range of 2.7V - 5.5V. The maximum sampling rate is 200 ksps at VDD = 5V and 75 ksps at VDD = 2.7V. The MCP3004/3008 are available in PDIP, SOIC and TSSOP packages.

This document describes Microchip Technology's PIC18F2423/2523/4423/4523 series 28/40/44-pin enhanced Flash microcontrollers with 12-bit A/D conversion and nanoWatt technology.

This document is about MCP73811/2 charge controller, which introduces its features and characteristics, including selectable charge current, voltage range, temperature range and more.

This document is the datasheet of MCP6L71/1R/2/4 series operational amplifiers, which introduces the features and characteristics of this series.