ANALOG Manuals

The AD586 is a high-precision 5V voltage reference that utilizes a proprietary ion-implanted buried Zener diode and laser-trimmed high stability thin-film resistors, providing outstanding performance at a low cost. The AD586 offers much higher performance than most other 5V voltage references.

The AD584 is an eight-terminal precision voltage reference offering pin-programmable selection of four popular output voltages: 10.000 V, 7.500 V, 5.000 V, and 2.500 V. It features high accuracy, no external components required, trimmed temperature coefficient, and stable output.

The AD581 is a three-terminal, temperature compensated, monolithic bandgap voltage reference which provides a precise 10.00 volt output from an unregulated input level from 12 to 30 volts. Laser Wafer Trimming (LWT) is used to trim both the initial error at +25°C as well as the temperature coefficient, which results in high precision performance previously available only in expensive hybrids or oven-regulated modules. The 5 mV initial error tolerance and 5 ppm/°C guaranteed temperature coefficient of the AD581L represent the best performance combination available in a monolithic voltage reference.

AD580 is a 2.5V reference voltage IC produced by AD company, with high accuracy, small package, low static current, good temperature drift and long-term stability.

The ADG608/ADG609 are monolithic CMOS analog multiplexers comprising eight single channels and four differential channels respectively, fully specified for ±5 V, +5 V and +3 V power supplies. The ADG608 switches one of eight inputs to a common output as determined by the 3-bit binary address lines A0, A1 and A2. The ADG609 switches one of four differential inputs to a common differential output as determined by the 2-bit binary address lines A0 and A1. An EN input on both devices is used to enable or disable the device. When disabled, all channels are switched OFF. All the address and enable inputs are TTL compatible over the full specified operating temperature range, making the parts suitable for bus-controlled systems such as data acquisition systems, process controls, avionics and ATEs since the TTL compatible address inputs simplify the digital interface design and reduce the board space.

CMOS Latched 8-/16-Channel Analog Multiplexers ADG526A/ADG527A are CMOS monolithic analog multiplexers with 16 single channels and dual 8 channels, respectively. These multiplexers feature 44 V maximum supply rating, VSS to VDD analog signal range, single- or dual-supply specifications, wide supply ranges (10.8 V to 16.5 V), microprocessor compatibility (100 ns WR pulse), extended plastic temperature range (-40°C to +85°C), low leakage (20 pA typical), low power dissipation (28 mW maximum), and are available in PDIP, CERDIP, SOIC, and PLCC packages.

ADG508A/ADG509A are CMOS monolithic analog multiplexers with eight channels and dual four channels, respectively. The ADG508A switches one of eight inputs to a common output, depending on the state of A0, A1, and A2 pins. The ADG509A switches two inputs to a common output, depending on the state of A0 and A1 pins.

The ADG506A and ADG507A are CMOS monolithic analog multiplexers with 16 channels and dual 8 channels, respectively. The ADG506A switches one of 16 inputs to a common output, depending on the state of four binary addresses and an enable input. The ADG507A switches one of eight differential inputs to a common differential output, depending on the state of three binary addresses and an enable input. Both devices have TTL and 5V CMOS logic compatible digital inputs.

The ADG428/ADG429 are analog multiplexers with low on resistance, low power consumption, and high speed.

ADG408/ADG409 are 8-channel and 4-channel single-ended/differential high performance analog switches, with a maximum supply voltage range of 44 V, VSS to VDD analog signal range, low on resistance (maximum 100 Ω), low power (ISUPPLY < 75 μA), fast switching, break-before-make switching action, and can replace DG408/DG409

This document describes the features and characteristics of ADI products from BDTI C company.

The AD781 is a high speed monolithic sample-and-hold amplifier (SHA). The AD781 guarantees a maximum acquisition time of 700 ns to 0.01% over temperature. The AD781 is specified and tested for hold mode total harmonic distortion and hold mode signal-to-noise and distortion. The AD781 is configured as a unity gain amplifier and uses a self-correcting architecture that minimizes hold mode errors and insures accuracy over temperature. The AD781 is self-contained and requires no external components or adjustments. The low power dissipation, 8-pin mini-DIP package and completeness make the AD781 ideal for highly compact board layouts. The AD781 will acquire a full-scale input in less than 700 ns and retain the held value with a droop rate of 0.01 µV/µs. Excellent linearity and hold mode dc and dynamic performance make the AD781 ideal for 12- and 14-bit high speed analog-to-digital conversion.

The AD585 is a high performance, precision sample-and-hold amplifier that is ideal for high speed 10- and 12-bit data acquisition systems.

The AD637 is a complete, high accuracy, monolithic rms-to-dc converter that computes the true rms value of any complex waveform. It offers performance that is unprecedented in low voltage, wideband applications.