TEXAS Manuals (Others)

The CDC3S04 is a four-channel low-power low-jitter sine-wave clock buffer. It can be used to buffer a single master clock to multiple peripherals. The four outputs (CLK1-CLK4) are designed for minimal channel-to-channel skew and ultralow additive output jitter. Each output has its own clock request inputs which enable the dedicated clock output. These clock requests are active-high (can also be changed to be active-low via I2C), and an output signal is generated that can be sent back to the master clock to request the clock (MCLK_REQ). MCKL_REQ is an open-source output and supports the wired-OR function (default mode)

File format: PDF Size:948 KB

The OPA379 is a low-noise, low-power operational amplifier that operates from a supply voltage as low as 1.8V. It is suitable for a wide range of battery-powered applications, such as portable devices, medical instruments, and handheld test equipment. The OPA379 features impressive bandwidth (90kHz), low bias current (25pA), and low noise (80nV/√Hz) relative to the very low quiescent current (5.5µA max).

File format: PDF Size:552 KB

The bq2002D/T is a low-cost CMOS battery charger controller that can provide reliable charge termination for both NiCd and NiMH battery applications.

File format: PDF Size:392 KB

The TLV1508 and TLV1504 are a family of high performance, 10-bit low power, 3.86µs, CMOS analog-to-digital converters (ADC) which operate from a single 2.7-V to 5.5-V power supply. The converters include an 8-byte FIFO for capturing conversion results. The TLV1508 and TLV1504 provide SPI (CPOL = 0, CPHA = 0)/DSP-compatible serial interfaces with SCLK up to 20 MHz.

File format: PDF Size:617 KB

This datasheet provides detailed information about the DAC7614, including its features and specifications.

File format: PDF Size:500 KB

The TPS61050 is a high-frequency synchronous boost converter with constant current control for driving single white LEDs. It can provide up to 1.2A of current. The device uses a small inductor and external components to minimize input ripple. The device also has a 250 mV LED feedback voltage to optimize efficiency. The TPS61050 can operate as either a constant current source or a standard voltage-boost regulator. This allows it to be used to power other high-power devices in the system, such as flashlights or flash cameras.

File format: PDF Size:1518 KB

This document describes the features and characteristics of Harris Semiconductor SCHS173A, including buffered inputs and outputs, four operating modes, typical propagation delay, etc.

File format: PDF Size:52 KB

This datasheet provides detailed information about the features of the SN74AVC8T245, including control input levels, VCC isolation, Ioff support, dual rail design, I/O port tolerance range, maximum data rate, latch-up performance and ESD protection.

File format: PDF Size:457 KB

This is a user's guide for the MSP-FET430 Flash Emulation Tool, which provides information on the installation and usage of the tool.

File format: PDF Size:4104 KB

SN54AHCT541 and SN74AHCT541 Octal buffers/drivers with 3-state outputs

File format: PDF Size:532 KB

The TPS22903 and TPS22904 are ultra-small, low rON single channel load switches with controlled turn on. The device contains a P-channel MOSFET that can operate over an input voltage range of 1.1V to 3.6V. The switch is controlled by an on/off input (ON), which is capable of interfacing directly with low-voltage control signals. In TPS22904, a 85-Ω on-chip load resistor is added for output quick discharge when switch is turned off.

File format: PDF Size:722 KB

The UCD9248 is a multi-rail, multi-phase synchronous buck digital PWM controller designed for non-isolated DC/DC power applications. It integrates dedicated circuitry for DC/DC loop management with flash memory and a serial interface to support configurability, monitoring and management.

File format: PDF Size:968 KB

the dac8534 is a quad channel, 16-bit digital-to-analog converter (dac) offering low-power operation and a flexible serial host interface. it can be used in portable instrumentation, closed-loop servo-control, process control, data acquisition systems, programmable attenuation and pc peripherals.

File format: PDF Size:374 KB

The TMP102 is a low-power digital temperature sensor with SMBus/Two-Wire serial interface available in a tiny SOT563 package. It does not require external components and can measure temperature with a resolution of 0.0625°C. The TMP102 features SMBus and two-wire interface compatibility, allowing up to four devices on one bus. It also has an SMB alert function. The TMP102 is ideal for extended temperature measurement in various fields such as communication, computer, consumer, environmental, industrial, and instrumentation. The device operates in a temperature range of -40°C to +125°C.

File format: PDF Size:460 KB

The SN54F245, SN74F245 are octal bus transceivers with 3-state outputs designed for asynchronous communication between data buses.

File format: PDF Size:498 KB

The LT1054 is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. It also provides regulation, a feature previously not available in switched-capacitor voltage converters.

File format: PDF Size:619 KB

SCES516E is a dual-bit noninverting bus transceiver that uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional dual-channel communication with data rates up to 420 Mbps.

File format: PDF Size:394 KB

File format: PDF Size:0 KB

This document describes the features and characteristics of the MSP430x20x1, MSP430x20x2, and MSP430x20x3 mixed signal microcontrollers, including low supply voltage range, ultralow power consumption, multiple power-saving modes, fast wake-up from standby mode, 16-bit RISC architecture, clock module configurations, timer, comparator, analog-to-digital converter, universal serial interface, brownout detector, and on-chip emulation logic.

File format: PDF Size:2529 KB

The DAC8218 is a low-power, octal, 14-bit digital-to-analog converter (DAC).

File format: PDF Size:2022 KB