Industrial

The STEVAL-ILL031V1 is a digital constant-current controller for LED driving based on the STM8S208x. It has a DC input voltage of 48V and adapts the output voltage through the Buck stage to drive LEDs with the selected current. The controller allows driving of 4 LED strings, managing up to 120W. Using 3W LEDs, each string can obtain 30W (10 LEDs in series in each string). Additionally, it features low voltage-sensing circuitry, logic level MOSFETs driven by the microcontroller without a gate driver (ground referred), and high efficiency (up to 98%).

This datasheet introduces the STEVAL-ICB004V1 board, including its features, such as four-wire resistive touch-sensing demonstration GUI, configurable touch-sensing parameters, STMPE811 GPIO expander functionality hardware support, STM32 microcontroller SPI and I2C interfaces USB universal dongle functionality, run-time application firmware upgrade using DFU, etc.

This document introduces the features and characteristics of STEVAL-ISW001V1 2.5 kW manual arc welding demonstration board, including input voltage, output voltage, output current, switching frequency and efficiency. The demonstration board is a platform for evaluating STMicroelectronics' silicon devices in high power/current applications, where the robustness and efficiency of the silicon devices used are the keys to a reliable system.

This data brief introduces the features of the STEVAL-ISF002V1 1.4 kW digital PFC demonstration board, including maximum output power, input voltage range, output voltage, power factor, total harmonic distortion, overcurrent protection, software current limitation, software overvoltage protection, software voltage limitation, zero load regulated DC output voltage, adjustable output DC voltage target value, embedded UI for real-time adjustment of voltage and current PI parameters, dual FOC motor control drive demonstration, RoHS compliance, etc.

This data sheet describes the features and characteristics of the STEVAL-IHM029V1 2000 W universal motor control demonstration board based on the STM8S103F2 MCU and T1235H Triac.

This document describes the features of STEVAL-ISA071V1 4 W non-isolated wide input-voltage range SMPS demonstration board, including input voltage range, output voltage range, maximum output power, standby power, short-circuit protection, isolation type, EMI and RoHS compliance.

The STEVAL-IHP001V3 is a ZigBee SmartPlug demonstration board based on the STM32F10x, SPZB260-PRO, and STPM01. It can monitor energy consumption and electrical parameters, enabling wireless home area network (HAN) energy management and remote load management.

The STEVAL-ISA018V1 is a resonant 150W (240W peak) switched-mode power supply demonstration board based on the L6599. It features a wide input voltage range, stable output voltage, and high efficiency.

This document is the data brief of the STEVAL-IHP003V1 module, which introduces the features of the module, including PLM communication protocol, FSK modulation, centre frequency, bitrate, microcontroller, network configuration, etc.

The STEVAL-PCC012V1 demonstration board is based on the STM32F107 and features Ethernet, USB OTG, and general-purpose extension connectors. It also has optional Wi-Fi module positions, a microSD card socket, and digital/analog extension connectors, etc.

This document describes a low-cost green-mode PWM controller for flyback converters. It features low start-up current, low operating current, support for the 'Blue Angel' standard, constant output power limit, and more.

SG6510X1 is a PC power supply voltage supervisor chip produced by System General Corp., with over-voltage and under-voltage protection functions, output pins include PGO and FPO, PGO is a power good signal, and FPO is a fault protection signal.

This datasheet introduces the features and characteristics of the STEVAL-TDR011V1 demonstration board, which is a two-stage 50 W RF power amplifier that includes an output LPF (low-pass filter) for harmonics rejection. It also features power detection and a temperature sensor. The main purpose of the board is to demonstrate the functioning and performance of the PD85006L-E and the STAP85050 devices from the LdmoST plastic family of RF power transistors. The application is specifically designed for 2-way analog and digital mobile radios.

This datasheet provides details of the STEVAL-ILB007V1 demo board, which can drive 2 x 58 W linear T8 fluorescent lamps.