ST Manuals

The TD350E is an advanced IGBT/MOSFET driver with features including 1.5A source/2.3A sink gate drive, active Miller clamp, two-level turn-off with adjustable level and delay, desaturation detection, fault status output, negative gate drive capability, input compatible with pulse transformer or optocoupler, separate sink and source outputs for easy gate driving, UVLO protection, and 2kV ESD protection. It is suitable for use in 1200V, 3-phase inverters, motor control, and UPS systems.

74VCX162244 is a 16-bit buffer with low voltage, high speed, low power, 3.6V input and output

The 74VCX162244 is a low voltage CMOS 16 BIT BUS BUFFER (NON INVERTED) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. Any nG output control governs four BUS BUFFERS. Output Enable input (nG) tied together gives full 16-bit operation. When nG is LOW, the outputs are on. When nG is HIGH, the output are in high impedance state. This device is designed to be used with 3 state memory address drivers, etc. The device circuits is including 26Ω series resistance in the outputs. These resistors permits to reduce line noise in high speed applications. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and trans

The 74VCX162245 is a low voltage CMOS 16 BIT BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs

The 74VCX162245 is a low voltage CMOS 16 BIT BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. This IC is intended for two-way asynchronous communication between data buses; the direction of data transmission is determined by DIR input. The two enable inputs nG can be used to disable the device so that the buses are effectively isolated.

TS616 is a dual operational amplifier from Texas Instruments, featuring low noise, high output current, low distortion, high gain and large bandwidth. It is suitable for xDSL, multiple video line drive and other applications.

The TS615 is a dual operational amplifier featuring a high output current 410mA, which can be configured differentially for driving signals in telecommunication systems using multiple carriers. The TS615 is ideally suited for xDSL (High Speed Asymmetrical Digital Subscriber Line) applications. This circuit is capable of driving a 10Ω or 25Ω load at ±2.5V, 5V, ±6V or +12V power supply. The TS615 will be able to reach a -3dB bandwidth of 40MHz on 25Ω load with a 12dB gain. This device is designed for the high slew rates to support low harmonic distortion and inter-modulation. The TS615 is fitted out with Power Down function to decrease the consumption. During this sleep state the device displays a short circuit output in order to keep the impedance matching with the line. The TS615 is housed in TSSOP14 Exposed-Pad plastic package for a very low thermal resistance.

The TS613 is a dual operational amplifier featuring a high output current, large gain-bandwidth product, and capable of driving a 25Ω load at ±6V power supply. This device is particularly intended for applications where multiple carriers must be amplified simultaneously with very low intermodulation products.

The KITHSEVAL/STDL high-speed operational amplifier evaluation board kit includes 5 unmounted evaluation boards, a CD-ROM of documentation, including a user manual for the boards, and datasheets for the supported high-speed operational amplifiers.

The TS612 is a dual operational amplifier featuring a high output current (200mA min.), large gain-bandwidth product (130MHz) and capable of driving a 25Ω load with a 160mA output current at ±6V power supply. This device is particularly intended for applications where multiple carriers must be amplified simulta- neously with very low intermodulation products. The TS612 is housed in SO20 batwing plastic package for a very low thermal resistance. It is also available in TSSOP14 plastic package. This tiny package comes very interesting for surface saving. The TS612 is fitted out with Power Down function in order to decrease the consumption.

The TS613 is an upgraded version of TS612 with high output current (200mA) and low noise (3nV/√Hz, 1.2pA/√Hz), suitable for applications where multiple carriers must be amplified simultaneously, such as the upstream line driver for Assymetric Digital Subscriber Line (ADSL).

This document describes a dual wideband operational amplifier, primarily used as an upstream line driver for Asymmetric Digital Subscriber Line (ADSL) (NT). The product features low noise, high output current, low harmonic and intermodulation distortion, and high slew rate.