ST Manuals

This is a BLDC motor control board based on ST7FMC MCU, supports 3 phase AC induction motor control, 3 phase BLDC/AC PM motor control (6 step sensorless), 3 phase BLAC PM motor control (sinusoidal driven, with Hall sensors)

This document is the data brief for STEVAL-ISA039V1 single phase 5A step-down converter evaluation board. It mainly introduces the input voltage, output voltage, output current and other characteristics of the product.

This document is a data brief for STMicroelectronics' STEVAL-ISA028V1 single phase 20A step-down converter evaluation board. The evaluation board is based on the L6727 chip and features an optimized BOM for 12V input / 1.25V output @ 20A, providing high flexibility for a wide range of designs. It supports customizable output voltage, compatibility with L6726A/L6727 controllers, and has a controller input voltage (VCC) range from 5V to 12V, with a conversion input voltage (VIN) up to 13.2V. It is compatible with DPAK / SO-8 / PowerSO-8 / PowerFLAT MOSFET, and supports multiple footprints for input and output capacitors, as well as through-hole / SMD inductor compatibility. The PCB is a 4-layer design. The evaluation board demonstrates the key features of STMicroelectronics' L6727 chip, which is a powerful buck controller that simplifies and reduces cost for the design of complete step-down voltage regulators.

The file introduces Hitex comSticks, a complete, low-cost evaluation and development packages that provide a fast and easy introduction to the networking features of Cortex™-M3 STM32 and ARM966E® core- based microcontroller families.

The L6902D evaluation board integrates the step-down switching regulator with adjustable current limit L6902D as well as the external components required for a typical application. The input voltage of the application board can range from 8V up to 25V due to the rated voltage of the input capacitor and the schottky rectifier repetitive peak reverse voltage (both 25V). The external resistor divider (R1 and R2) sets the output voltage of the application board to 3.3V. A different output voltage can be regulated from 1.235V up to 10V, which is the rated voltage of the output capacitor. A current limit of 1A is programmed by the 100mΩ sense resistor Rsense. The inductor saturation current and the forward current of the schottky rectifier fit the current limit setting.

This document introduces STEVAL-IFP001V1, an 8-channel high-side driver demonstration board based on VIPower M0-3 proprietary technology, for industrial applications.

The EVALST7538DUAL board integrates the ST7538 power line transceiver along with the power supply section, the signal coupling interface section, crystal oscillator and device protections. The coupling interface section has been realized for communication on CENELEC Band A used mainly for AMR applications, with the possibility of programmable switching between 72kHz and 86kHz communication channels. This half-duplex “dual channel” communication feature has been implemented through optimized receiving and transmitting filters on the board. EVALST7538DUAL board must be connected to a PC through the EVALCOMMBOARD general purpose board. The dedicated SW running on the PC can be downloaded from “www.st.com/powerline” web page.

evalcommboard is a general purpose board based on a st72f651ar6 usb microcontroller providing a standard 12mbps usb main interface connecting a controlling pc and different reference design boards.

Introduces the REva starter kits, Raisonance's complete, cost-effective solutions for starting application development and evaluating STM8x, ST7LITEx, ST7Fox, ST7232x, ST7234x, ST7236x and ST7263B microcontrollers

The IAR KickStart Kits™ are complete, cost-effective solutions for starting application development and evaluating the STMicroelectronics STR91x, STR75x, STR73x and STR71x ARM core-based microcontrollers.

The document describes the Raisonance REva Starter Kits, which are complete and low-cost solutions for starting application development and evaluating the features of STMicroelectronics' ARM® Cortex™- M3, ARM966E™, and ARM7 series products.

ST7232X-EVAL is an adaptable, full-featured evaluation board that allows you to try out the features of the ST7232x and ST7252x, and develop applications for these microcontrollers.

The ST7MC-KIT/BLDC is an integrated system designed to provide you with a complete, ready-to-use motor control application for the ST7MC family of microcontrollers. It allows real-time control of three-phase brushless DC and AC motors in all control topologies from a PC-based GUI, or in standalone operation.

STR910-EVAL is a development platform for STMicroelectronic’s ARM® core-based STR91xF microcontrollers, includes high performance STR910F microcontroller, which is based on the ARM966ES core and includes Pre-fetch Queue and Branch cache, full speed USB 2.0 compatible port, Ethernet 100/10 interface, Embedded MAC, CAN 2.0B compliant interface, large Dual Bank Flash memory, large SRAM and many peripherals.

This application note presents the clock system configuration tool for the STM32F0xx microcontroller family. The purpose of this tool is to help the user configure the microcontroller clocks, taking into consideration product parameters such as power supply and Flash access mode.