ANALOG Manuals

The ADP8861 Rev. B is a charge pump with automatic gain selection of 1×, 1.5×, and 2× for maximum efficiency, and can drive up to 7 LEDs independently with a maximum current of 30 mA (typical) for each channel.

ADP1655 is a high efficiency dual LED flash driver that utilizes a 2MHz synchronous PWM boost converter, an integrated 2.2µH power inductor and features I2C programmable functionality.

ADF702X Development Platform Quick Start Guide is a quick start guide for Analog Devices' ADF702X Development Platform, which introduces the features, contents, working principles, hardware and software of the ADF702X Development Platform

The AD8213 is a dual-channel, precision current sense amplifier with features such as high common-mode voltage range, wide operating temperature range, and excellent ac and dc performance.

The ADuM1234 is an isolated, half-bridge gate driver that employs the Analog Devices, Inc. iCoupler® technology to provide independent and isolated high-side and low-side outputs. Combining high speed CMOS and monolithic transformer technology, the ADuM1234 achieves high precision while maintaining high isolation voltage and output current.

The AD584 is an eight-terminal precision voltage reference circuit that offers pin-programmable selection of four popular output voltages: 10.000 V, 7.500 V, 5.000 V, and 2.500 V. Its features include: programmable output voltages, high accuracy, no external components required, trimmed temperature coefficient, zero output strobe terminal, two-terminal negative reference capability, output sources or sinks current, low quiescent current, and high current output capability.

ADIS16204 is a programmable high-g digital impact sensor and recorder. It features dual-axis sensing, high resolution, and programmable event recording.

The AD8565/AD8566/AD8567 are low cost, single supply rail-to-rail input and output operational amplifiers optimized for LCD monitor applications. They are built on an advanced high voltage CBCMOS process and feature high slew rates, 35 mA continuous output drive, 250 mA peak output drive, low input bias voltage, low noise and high common mode rejection ratio.

The AD818 is a low cost video op amp optimized for use in video applications that require gains equal to or greater than +2 or -1.

The 7B14 series modules are signal conditioners that amplify, protect, filter, and isolate input voltages from a wide variety of two and three-wire platinum, copper, and nickel Resistor Temperature Detectors (RTDs). The module provides a precision output of either +1V to +5V or 0V to +10V, linear with temperature. All 7B14 series modules are mix-and-match and hot swappable.

AD261 is a high speed logic isolator produced by Analog Devices. It has five isolated logic lines that are available in six I/O configurations.

AD5302/AD5312/AD5322 is a dual rail-to-rail voltage output 8-/10-/12-bit DAC with a power supply range of +2.5V to +5.5V. It features micropower operation, power-down mode, double-buffered input logic, etc.

AD5744R is a 14-bit high-precision serial input bipolar voltage output DAC introduced by Analog Devices. The chip has three programmable output ranges: ±10 V, ±10.2564 V, and ±10.5263 V. The output noise is 60 nV/√Hz, and the settling time is 10 μs. It has integrated reference buffers, internal reference, temperature sensor, short circuit protection, LDAC synchronous update, CLR asynchronous reset and other functions. It is suitable for industrial automation, open/closed loop servo control, process control, data acquisition systems and other fields.

The AD679 is a 14-bit 128 kSPS complete sampling ADC that combines a high-speed sample-hold amplifier (SHA), ADC, 5 V reference, clock, and digital interface on a single chip. It provides a fully specified sampling A/D function unattainable with discrete designs.

AD7466/AD7467/AD7468 are 1.8V to 3.6V micro-power 8/10/12-bit ADCs with features including low power consumption, fast throughput rate, wide input bandwidth, and compatibility with multiple interfaces. They are suitable for applications such as battery-powered systems, medical instruments, and remote data acquisition.