ANALOG Manuals

The AMP01 is a monolithic instrumentation amplifier designed for high-precision data acquisition and instrumentation applications. The design combines the conventional features of an instrumentation amplifier with a high current output stage. The output remains stable with high capacitance loads (1 µF), a unique ability for an instrumentation amplifier. Consequently, the AMP01 can amplify low level signals for transmission through long cables without requiring an output buffer. The output stage may be configured as a voltage or current generator. Input offset voltage is very low (20 µV), which generally eliminates the external null potentiometer. Temperature changes have minimal effect on offset; TCVIOS is typically 0.15 µV/°C. Excellent low-frequency noise performance is achieved with a minimal compromise on input protection. Bias current is very low, less than 10 nA over the military temperature range. High common-mode rejection of 130 dB, 16-bit linearity at a gain of 1000, and 50 mA peak output current are achievable simultaneously.

File format: PDF Size:226 KB

The AD524 is a precision instrumentation amplifier from Analog Devices. It features low noise, low nonlinearity, high CMRR, low offset voltage, low offset voltage drift, high gain bandwidth product and pin programmable gains of 1, 10, 100, 1000. It also has input protection, switch mode power supply and no external components required.

File format: PDF Size:604 KB

SDC/RDC1767/1768

File format: PDF Size:456 KB

AD5749 is a single-channel, low-cost, high-precision, current output driver with programmable output range through hardware or software programming. The main features include: programmable current output range, low total unadjusted error (TUE), low output temperature drift, open circuit protection, and flexible serial interface.

File format: PDF Size:587 KB

The document provides information about the AD5749 industrial current output driver. The product features a single-supply design, a maximum supply of 55V, and programmable ranges.

File format: PDF Size:387 KB

AD5748 is a single-channel, low-cost, high-precision voltage/current output driver that can be programmed to set the output range through hardware or software. It features a flexible serial digital interface, on-chip output fault detection, PEC error checking, and more. It is suitable for process control, actuator control, PLC, and other applications.

File format: PDF Size:1047 KB

The AD5751 is a single-channel, low-cost, precision, voltage/current output driver with hardware or software programmable output ranges. The software ranges are configured via the I2C interface. The AD5751 features low output voltage drift (5 ppm/°C) and a wide operating temperature range (-40°C to +105°C).

File format: PDF Size:267 KB

AD5750 is a single-channel, low-cost, high-precision voltage/current output driver with programmable output range through hardware or software. Software output range can be set through SPI/MICROWIRE™ compatible serial interface. AD5750 can meet the requirements of PLC and industrial process control applications.

File format: PDF Size:831 KB

AD5750 is a single channel, low-cost, precision, voltage/current output driver produced by Analog Devices. It has multiple output current/voltage ranges to meet the needs of different application scenarios. The input of the driver is a single-ended digital signal, which can be configured through the I2C interface. AD5750 has overcurrent protection, PEC error checking, and clear functions to improve system safety and reliability.

File format: PDF Size:254 KB

AD5410/AD5420 is a 12/16-bit, 4mA~20mA current output, 12/16-bit DAC with SPI/I2C/MICROWIRE interface. It can be used for various current source applications, including current drivers, battery dischargers, battery chargers, current detectors and current loop control.

File format: PDF Size:910 KB

The AD5410/AD5420 is a low-cost, precision, fully integrated 12-/16-bit converter offering a programmable current source output designed for control applications.

File format: PDF Size:685 KB

This data sheet describes the ADL5201, an integrated circuit for high-frequency digitally controlled VGA. The device has a wide dynamic range and high output power, making it suitable for use in a variety of applications, including differential ADC drivers, high IF sampling receivers, high output power IF amplifiers, and instrumentation.

File format: PDF Size:995 KB

This document describes the features and characteristics of the ADL5202 VGA, including wide dynamic range, high speed, and digital control.

File format: PDF Size:1197 KB

The ADL5240 is a high performance, digitally controlled VGA that operates from 100 MHz to 4000 MHz. It features serial and parallel interfaces, a 6-bit, 0.5 dB digital step attenuator, 31.5 dB gain control range with ±0.25 dB step accuracy.

File format: PDF Size:1061 KB

ADL5243 is a high performance digitally controlled VGA. It supports serial and parallel interfaces, has a 6-bit 0.5dB digital step attenuator, a 31.5dB gain control range, and ±0.25dB step accuracy.

File format: PDF Size:1031 KB

The AD8372 is a 41dB dynamic range, 1dB gain step programmable dual VGA from Analog Devices. It supports single-ended input and differential output. The device is applied to differential ADC drivers, CMTS upstream direct sampling receivers, CATV modem signal scaling, generic RF/IF gain stages, single-ended to differential conversion, etc.

File format: PDF Size:605 KB

AD8376 is a dual channel digitally controlled VGA from Analog Devices with ultralow distortion. It has a bandwidth of 700 MHz, gain range of -4 dB to +20 dB, step size of 1 dB ± 0.2 dB, differential input and output, noise figure of 8.7 dB @ maximum gain, output IP3 of ~50 dBm at 200 MHz, output P1dB of 20 dBm at 200 MHz, dual parallel 5-bit control interface, provides constant SFDR vs. gain, power-down control, single 5 V supply operation, and a 32-lead, 5 mm x 5 mm LFCSP package. It is suitable for differential ADC drivers, main and diversity IF sampling receivers, wideband multichannel receivers, and instrumentation.

File format: PDF Size:1008 KB

AD8370 is a low cost, digitally controlled, variable gain amplifier (VGA) that provides precision gain control, high IP3, and low noise figure. Its excellent distortion performance and wide input dynamic range make it suitable for a variety of applications, such as differential ADC drivers, IF sampling receivers, RF/IF gain stages, cable and video applications, SAW filter interfacing, and single-ended-to-differential conversion.

File format: PDF Size:802 KB

AD8324 is a low-cost amplifier designed for coaxial line driving. It supports DOCSIS 2.0 and Euro-DOCSIS standards and has programmable gain in 1 dB steps over a range of 59 dB. It has low distortion with -59 dBc SFDR at 21 MHz and -54 dBc SFDR at 65 MHz output at 61 dBmV. The output noise level at minimum gain is 1.3 nV/√Hz. It maintains a 75 Ω output impedance in TX-enable and Transmit-disable condition. The upper bandwidth is 100 MHz (full gain range). It supports 3.3 V supply operation and SPI interfaces.

File format: PDF Size:406 KB

The AD8328 is a 5 V supply, DOCSIS and EuroDOCSIS compliant, programmable gain, dual input single ended output upstream cable line driver. This device supports SPI interface for programming, supports Tx-enable and Tx-disable two working modes, output impedance is 300 Ω and upper bandwidth is 107 MHz.

File format: PDF Size:620 KB