TEXAS Manuals

SN54AHCT14, SN74AHCT14 HEX SCHMITT-TRIGGER INVERTERS are Hex Schmitt-Trigger Inverters produced by Linear Technology. These products have excellent performance and can meet TTL voltage compatible, 250 mA latch-up performance, 2000-V human-body model, 200-V machine model and 1000-V charged device model requirements.

XIO2000A is Texas Instruments' PCI Express bridge chip, designed for seamless migration from legacy PCI to the PCI Express interface. The chip supports PCI Express rates of 2.5 Gbps and PCI 2.3 interface. XIO2000A enables PC and I/O add-on card manufacturers to begin transitioning to native PCI Express technology while preserving compatibility with existing PCI system software and firmware.

This product is a high-performance floating-point digital signal processor (DSP)

The document describes the features and characteristics of the REF30xx series precision, low power, low dropout voltage references. The series is available in a tiny SOT23-3 package, making it ideal for portable and battery-powered applications. The series does not require a load capacitor but is stable with any capacitive load. All models are specified for the wide temperature range of -40°C to +125°C.

This document describes the features and characteristics of the PTH12040W adjustable power module, including a high output current of up to 50A, an input voltage range of 8V to 14V, a wide output voltage adjustment range of 0.8V to 5.5V, and various protection and control features.

This document describes the features and characteristics of the PTH05020W series non-isolated power modules, including up to 22A output current, 5V input voltage, wide-output voltage adjust (0.8V to 3.6V), efficiencies up to 96%, 155W/in³ power density, etc.

The PT7600 is a high-performance 10 Amp Integrated Switching Regulator (ISR) designed for easy integration of high-speed low-voltage microprocessors and bus drivers into existing 5V systems. It features high efficiency, wide input voltage range, and differential remote sense. It requires 1200µF of output capacitance.

This document introduces the PT5020 series of integrated switching regulators (ISRs), which convert a positive input voltage to a negative output voltage for a wide range of analog and datacom applications. These Plus to Minus ISRs incorporate a “Buck-Boost” topology and are packaged in the 3-pin, single in-line pin (SIP) package configuration.

This document introduces the TPS6040x family of products, which are devices that generate an unregulated negative output voltage from an input voltage ranging from 1.6V to 5.5V. The series features a wide input voltage range, only three small 1μF ceramic capacitors required, and a maximum output current of 60mA.

This document describes the features and characteristics of XIO3130, including power-up/power-down sequencing, Express interface, GPIO terminals, serial EEPROM, switch reset features, etc.

The TS2PCIE2212 is a PCI Express™ signal switch produced by Texas Instruments that can implement 1:2 multiplexing/demultiplexing of two pairs of PCI Express™ channels and supports a data rate of 2.5 Gbps.

ADS1274/ADS1278 is a 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) from Texas Instruments that supports data rates up to 128ksps and simultaneous sampling of four/eight channels. The devices in this series use a new digital filter design that provides 62kHz bandwidth and 111dB SNR (High-Resolution Mode), making them well-suited for high-precision, high-bandwidth measurement applications.

The CY74FCT163952 and CY74FCT163H952 are low-power, pin-compatible replacements for the LCX and LPT families, with 5V-tolerant inputs and outputs, 24 mA balanced-drive outputs, power-off disable outputs that permit live insertion, edge-rate control circuitry for reduced noise, FCT-C speed at 4.4 ns, latch-up performance that exceeds JEDEC Standard No. 17, typical output skew less than 250 ps, industrial temperature range of -40˚C to +85˚C, TSSOP (19.6-mil pitch) or SSOP (25-mil pitch), typical Volp (ground bounce) performance that exceeds Mil Std 883D, VCC = 2.7V to 3.6V, ESD (HBM) > 2000V, bus hold on data inputs, eliminates the need for external pull-up or pull-down resistors, devices with bus hold are not recommended for translating rail-to-rail CMOS signals to 3.3V logic levels