ANALOG Manuals

The ADN4665 is a 3V, LVDS, Quad, CMOS differential line driver. It has ±15kV ESD protection, 400 Mbps (200 MHz) switching rates, 100 ps typical differential skew, 400 ps maximum differential skew, 2 ns maximum propagation delay, 3.3 V power supply, ±350 mV differential signaling, low power dissipation (13 mW typical), interoperability with existing 5 V LVDS receivers, high impedance on LVDS outputs on power-down, compliance with TIA/EIA-644 LVDS standards, industrial operating temperature range of -40°C to +85°C, and is available in surface-mount SOIC package and low profile TSSOP package.

ADN4666 is a 3.3V LVDS quad CMOS differential line receiver with ±8kV ESD IEC 61000-4-2 contact discharge, 400Mbps (200MHz) switching rates, 100ps channel-to-channel skew, 100ps differential skew, 3.3ns propagation delay, 3.3V power supply, high impedance outputs on power-down, low power design, 10 mW quiescent typical power consumption, interoperable with existing 5V LVDS drivers, supports small swing (350 mV typical) differential input signal levels, supports open, short, and terminated input fail-safe, conforms to TIA/EIA-644 LVDS standard, industrial operating temperature range of -40°C to +85°C, available in surface-mount SOIC package and low profile TSSOP package.

ADN4667 is a quad, CMOS, low voltage differential line driver with features such as high ESD protection, high switching rates, simplified PCB layout, low power dissipation, interoperability with existing 5V LVDS receivers, etc.

The 3 V LVDS Quad CMOS Differential Line Receiver ADN4668 is a four-channel CMOS differential line receiver from Analog Devices. It has a 3.3 V power supply, supports 400 Mbps (200 MHz) switching rates, and has ±15 kV ESD protection on the receiver input pins. It supports small swing (310 mV typical) differential input signal levels, supports open, short, and terminated input fail-safe, and conforms to the TIA/EIA-644 LVDS standard.

This document describes the features and characteristics of the ADN4691E/ADN4693E/ADN4696E/ADN4697E high-speed M-LVDS transceivers, including operating voltage, data transfer rate, half-duplex and full-duplex modes, etc.

This document describes the features and characteristics of the ADN4690E/ADN4692E/ADN4694E/ADN4695E series high-speed M-LVDS transceivers, including a working voltage of 3.3V, support for half-duplex and full-duplex modes, support for data transfer rates of 100Mbps, compliance with the TIA/EIA-899 standard, and features such as interference resistance and ESD protection.

ADP5585 is a programmable logic block with 16 I/O for keypad decoding, GPIO, PWM generation, I2C interface, etc.

The ADP5587 is an I/O port expander and keypad matrix designed for QWERTY phones that require a large keypad matrix and expanded I/O lines. It features 18 GPIOs, 10×8 keypad matrix, I2C interface with auto-increment, 1.65V to 3.6V operation, keypad lock capability, open-drain interrupt output, key press and key release interrupts, GPI interrupt with level programmability, programmable pull-ups, key event counter with overflow interrupt, 275 μs debounce on the reset line and GPIs, 1 μA typical idle current, 55 μA typical polling current, 4 mm × 4 mm LFCSP package, small 2 mm x 2 mm WLCSP package, 0.4 mm pitch, multiple I2C addresses available for the LFCSP package to allow multiple port expanders on the same bus.

The ADP5588 is an I/O port expander and keypad matrix designed for QWERTY type phones that require a large keypad matrix and expanded I/O lines. It features 18 GPIO port expander or 10 × 8 keypad matrix, configurable to GPIs, GPOs, and keypad rows or columns. It also has dual light sensor inputs, I2C interface, configurable pull-ups, and more.

The ADP5589 is a keypad decoder and I/O expander from Analog Devices (ADI). It supports a 16-element FIFO for event recording and has 19 configurable I/Os that can be used for keypad decoding, key press/release interrupts, key pad lock/unlock, GPIO functions, etc.

ADM3232E is a 3.3 V RS-232 line driver/receiver with ±15 kV ESD protection. It meets EIA-232E specifications and has a data rate of 460 kbps. The product is suitable for general-purpose RS-232 data links, portable instruments, handsets, industrial/telecom diagnostic ports, and other applications.

This document introduces the features and characteristics of the ADM3307E/ADM3310E/ADM3311E/ADM3312E/ADM3315E series of products. This series of products are 2.7 V to 3.6 V power supply serial port transceivers with Green Idle low power mode, single power supply, 3 V logic, 0.1 μF to 1 μF charge pump capacitors, low EMI, low power shutdown: 20 nA, full RS-232 compliance, 460 kb/s data rate, one receiver active in shutdown (ADM3307E/ADM3311E/ADM3312E/ADM3315E), two receivers active in shutdown (ADM3310E), ESD>15 kV IEC 1000-4-2 on RS-232 I/Os, ESD>15 kV IEC 1000-4-2 on CMOS and RS-232 I/Os (ADM3307E).

The ADM2209E is a dual RS-232 port transceiver with ESD protection and standby.

ADM101E is a tiny RS-232 transceiver designed for portable applications. It features a transmission rate of 460 kbit/s and is compatible with RS-232 input/output levels. The transceiver operates from a single 5V power supply and includes one driver and one receiver. It also incorporates an on-board DC-DC converter, eliminating the need for a negative power supply. The ADM101E is low power and has an ultralow power shutdown mode. It is suitable for mobile telephones, palmtop computers, PDAs, portable instrumentation, and GPS receivers.

ADM206E/ADM207E/ADM208E/ADM211E/ADM213E are ±15 kV ESD-Protected, RS-232 Line Drivers/Receivers that comply with the 89/336/EEC EMC directive