ON Manuals (Industrial)

ON Semiconductor NCV4279C handbook

The NCV4279C is a 5.0 V precision micropower voltage regulator with an output current capability of 150 mA. The output voltage is accurate within ±2.0% with a maximum dropout voltage of 0.6 V at 150 mA. It has a low quiescent current of only 130 μA with a 100 μA load. This regulator is ideal for battery-operated microprocessor equipment. It features microprocessor control logic with an active RESET (with DELAY) and a FLAG monitor, which provides an early warning signal to the microprocessor of a potential impending RESET signal. The FLAG monitor allows the microprocessor to finish any signal processing before the RESET shuts it down. The active RESET circuit operates correctly at an output voltage as low as 1.0 V. The RESET function is activated during the power-up sequence or if the output voltage drops outside the regulation limits during normal operation. The reset threshold voltage can be decreased by connecting an external resistor divider to the RADJ lead. The regulator is protected against reverse battery, short circuit, and thermal overload conditions. It can withstand load dump transients, making it suitable for automotive environments. The device has also been optimized for EMC conditions.

File format: PDF Size:92 KB

ON Semiconductor LM358 LM258 LM2904 LM2904A LM2904V NCV2904 handbook

This document introduces the features and characteristics of the LM358/D series dual operational amplifiers, including low power consumption, single or dual power supply, input voltage range extended to ground/VEE, etc.

File format: PDF Size:138 KB

ON NCS2002 NCV2002 Sub-One Volt Rail-to-Rail Operational Amplifier with Enable Feature handbook

The NCS2002 is an industry first sub−one volt operational amplifier that features a rail−to−rail common mode input voltage range, along with rail−to−rail output drive capability. This amplifier is guaranteed to be fully operational down to 0.9 V, providing an ideal solution for powering applications from a single cell Nickel Cadmium (NiCd) or Nickel Metal Hydride (NiMH) battery. Additional features include no output phase reversal with overdriven inputs, trimmed input offset voltage of 0.5 mV, extremely low input bias current of 40 pA, and a unity gain bandwidth of 1.1 MHz at 5.0 V. The NCS2002 also has an active high enable pin that allows external shutdown of the device. In the standby mode, the supply current is typically 1.9 μA at 1.0 V. Because of its small size and enable feature, this amplifier represents the ideal solution for small portable electronic applications.

File format: PDF Size:131 KB

ON MC1455 MC1455B NCV1455B Timers handbook

The MC1455 is a highly stable timing circuit capable of producing accurate time delays or oscillation. It has additional terminals for triggering or resetting if desired. In the time delay mode, time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free-running frequency and the duty cycle are both accurately controlled with two external resistors and one capacitor. The circuit may be triggered and reset on falling waveforms, and the output structure can source or sink up to 200 mA or drive MTTL circuits.

File format: PDF Size:151 KB

ON MC34063A MC33063A NCV33063A 1.5 A Step Up/Down/ Inverting Switching Regulators handbook

The MC34063A Series is a monolithic control circuit containing the primary functions required for DC−to−DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically designed to be incorporated in Step−Down and Step−Up and Voltage−Inverting applications with a minimum number of external components. Refer to Application Notes AN920A/D and AN954/D for additional design information.

File format: PDF Size:169 KB

ON NCV1009 2.5 Volt Reference handbook(1)

The NCV1009 is a precision trimmed 2.5 V ±5.0 mV shunt regulator diode. The low dynamic impedance and wide operating current range enhances its versatility. The tight reference tolerance is achieved by on−chip trimming which minimizes voltage tolerance and temperature drift. A third terminal allows the reference voltage to be adjusted ±5.0% to calibrate out system errors. In many applications, the NCV1009Z can be used as a pin−to−pin replacement of the LT1009CZ and the LM136Z−2.5 with the external trim network eliminated.

File format: PDF Size:55 KB

ON NCV1009 2.5 Volt Reference datasheet(1)

The NCV1009 is a precision trimmed 2.5 V ±5.0 mV shunt regulator diode. It has low dynamic impedance and wide operating current range. On−chip trimming minimizes voltage tolerance and temperature drift. A third terminal allows the reference voltage to be adjusted ±5.0% to calibrate out system errors.

File format: PDF Size:55 KB

ON NUP4302MR6 Schottky Diode Array for Four Data Line ESD Protection handbook

The product is a Schottky diode array, mainly used for ESD protection of high-speed data line interface. The product has the characteristics of low voltage drop, fast switching, PN junction guard ring and so on.

File format: PDF Size:82 KB

ON NUP4301MR6T1 Low Capacitance Diode Array for ESD Protection in Four Data Lines handbook

NUP4301MR6T1 is a low capacitance diode array for ESD protection in four data lines. It is designed to protect sensitive components from possible harmful electrical transients, for example, ESD (electrostatic discharge).

File format: PDF Size:46 KB

ON NUP4201MR6 Low Capacitance TSOP-6 Diode-TVS Array for High Speed Data Lines Protection handbook

The NUP4201MR6 is a low capacitance, low power TVS diode that is designed to protect high speed data lines from ESD, EFT, and lighting. It features a 3pF maximum capacitance between I/O lines and is certified to IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5, and other international standards.

File format: PDF Size:42 KB

ON NUP4201DR2 Advance Information Low Capacitance Surface Mount TVS for High-Speed Data Interfaces handbook

NUP4201DR2 is a transient voltage suppressor from Semiconductor Components Industries, LLC. It is designed to protect equipment attached to high speed communication lines from ESD, EFT, and lighting.

File format: PDF Size:75 KB

ON NUP4201DR2 Low Capacitance Surface Mount TVS for High-Speed Data Interfaces handbook

The NUP4201DR2 is a low-capacitance surface mount TVS for high-speed data interfaces, designed to protect equipment attached to high speed communication lines from ESD, EFT, and lightning.

File format: PDF Size:75 KB

ON NUP4108W5 Low Capacitance Quad Array for ESD Protection handbook

The NUP4108W5 is a low capacitance quad array ESD protection device designed by Semiconductor Components Industries. It is suitable for applications requiring transient overvoltage protection, such as computers, printers, business machines, communication systems, medical equipment, etc. This device uses SC-88A SMT packaging and has the characteristics of small size, low power consumption and low capacitance.

File format: PDF Size:112 KB

ON NUP2301MW6T1 Low Capacitance Diode Array for ESD Protection in Two Data Lines handbook

NUP2301MW6T1 is a low capacitance diode array for ESD protection in two data lines. The device is designed to provide protection for sensitive components from possible harmful electrical transients; for example, ESD (electrostatic discharge).

File format: PDF Size:91 KB

ON Semiconductor NUP4103FC handbook

NUP4103FC is a quad ESD array device released by Semiconductor Components Industries, LLC. It has an ultra-small flip chip packaging and a high anti-ESD capability, suitable for scenarios where board space is a premium.

File format: PDF Size:62 KB

ON NUP2201MR6 Low Capacitance TSOP-6 Diode-TVS Array for High Speed Data Lines Protection handbook

The NUP2201MR6 is a low capacitance TSOP-6 diode TVS array for protection of high speed data lines.

File format: PDF Size:40 KB

ON Semiconductor NZL5V6ATT1 handbook

This document introduces a dual common anode zener diode for providing transient overvoltage protection capability. The product is intended for use in applications requiring voltage and ESD sensitive equipment, such as computers, printers, business machines, communication systems, medical equipment, etc. Its dual junction common anode design can protect four separate lines using only one package. The product is ideal for situations where board space is limited.

File format: PDF Size:41 KB

ON Semiconductor NUP1105L handbook

NUP1105L is an Onsemi single line LIN/CAN bus protector, which is packaged in SOT-23. It provides bidirectional protection for the data line, offering a low cost option for system designers to improve system reliability and meet stringent EMI requirements.

File format: PDF Size:42 KB

ON Semiconductor NUF6406MN handbook

This is a document about NUF6406MN low capacitance 6 line EMI filter with ESD protection. The device is designed for wireless applications and provides greater than -30 dB attenuation at frequencies ranging from 800 MHz to 2.4 GHz. It also offers ESD protection to clamp transients from static discharges. The device features EMI filtering and ESD protection, integrating 30 discrete components. It complies with IEC61000-4-2 (Level 4) with a rating of >8.0 kV (Contact). It is packaged in a 1.35 x 3.0 mm DFN package with moisture sensitivity level 1. The ESD ratings include machine model = C and human body model = 3B.

File format: PDF Size:49 KB

Brands



Products