LINEAR Manuals

LT1461 family of low dropout micropower bandgap references combine very high accuracy and low drift with low supply current and high output drive.

File format: PDF Size:249 KB

The LT1720/LT1721 are single supply 3V/5V comparators with 4.5ns response time and rail-to-rail outputs, making them well suited for TTL and CMOS circuits.

File format: PDF Size:263 KB

The LT3800 is a high-voltage synchronous current mode step-down controller with a fixed frequency of 200kHz. It can drive standard gate N-channel power MOSFETs and operate with input voltages from 4V to 60V.

File format: PDF Size:246 KB

The LTC4054-4.2/LTC4054X-4.2 is a standalone linear Li-Ion battery charger with thermal regulation in ThinSOT from Linear Technology Corporation. It features programmable charge current up to 800mA, no external MOSFET, sense resistor or blocking diode required, and a complete linear charger in ThinSOT package for single cell lithium-ion batteries.

File format: PDF Size:165 KB

The LT1220 is a high performance high speed operational amplifier with high input impedance, low input bias current, high gain bandwidth and high output swing. The device is suitable for a variety of applications requiring high precision and high speed, such as data acquisition systems, buffers, cable drivers, etc.

File format: PDF Size:262 KB

LTC3713 is a low input voltage, high power, no current sense synchronous buck DC/DC controller. It features adjustable current limit, adjustable frequency, 0.8V ±1% reference voltage, etc. It is suitable for applications such as telecom cards and bus termination.

File format: PDF Size:310 KB

LTC1628/LTC1628-PG are high efficiency dual 5V/3.3V step-down converters with various features such as high efficiency, 2-phase synchronous switching regulators, output voltage accuracy, dual N-channel MOSFET synchronous drive, power good output voltage monitor, adjustable soft-start current ramping, etc.

File format: PDF Size:382 KB

The LTC4556 provides all necessary power control, level translation and supervisory functions for a smart card or S.A.M. card interface. The part contains a low noise charge pump plus LDO for generating VCC power, as well as all necessary level shifting circuitry. The card voltage can be set to either 1.8V, 3V or 5V. The LTC4556 includes a card detection channel with automatic debounce circuitry. To reduce wiring costs, the LTC4556 interfaces to a microcontroller via a simple 4-wire serial interface. Multiple devices may be connected in daisy-chain fashion so that the number of wires to the card socket board is independent of the number of sockets. Status data is returned over the same interface. Extensive security features ensure proper deactivation sequencing in the event of a supply fault or a smart card electrical fault. The smart card pins can withstand greater than 10kV ESD in-situ with no additional components. The LTC4556 is available in a small, low profile (0.75mm), 4mm × 4mm QFN package.

File format: PDF Size:243 KB

The LTC3717 is a synchronous step-down switching regulator controller from Texas Instruments for DDR and QDR memory termination. The controller uses a valley current control architecture to deliver very low duty cycles without requiring a sense resistor. Operating frequency is selected by an external resistor and is compensated for variations in VIN. Forced continuous operation reduces noise and RF interference. Output voltage is internally set to half of VREF, which is user programmable. Fault protection is provided by an output overvoltage comparator and optional short-circuit shutdown timer. Soft-start capability for supply sequencing is accomplished by internally compensating VIN's variation with switching frequency.

File format: PDF Size:256 KB

LTC2926 is a MOSFET-controlled power supply tracker that allows tracking and sequencing of up to three power supply rails. It features adjustable ramp rates, offsets, and time delays, and automatic remote sense switching to compensate for voltage drops across the MOSFETs. The product is suitable for VCORE and VI/O supply tracking, microprocessor, DSP and FPGA supplies, servers, communication systems, etc.

File format: PDF Size:533 KB

The LT ®1765 is a monolithic buck switching regulator from Texas Instruments. It integrates a high efficiency 3A, 0.09Ω switch and all the control circuitry required to construct a high frequency, current mode switching regulator. The chip can operate at a wide input voltage range of 3V to 25V and output a maximum current of 3A.

File format: PDF Size:216 KB

LTC1645 1645fa Dual-Channel Hot Swap Controller/Power Sequencer

File format: PDF Size:326 KB

The LT ®1950 is a wide input range, single switch PWM controller that drives an N-channel power MOSFET with few external components required.

File format: PDF Size:214 KB

File format: PDF Size:0 KB

The LTC3568 is a constant frequency, synchronous step-down DC/DC converter. It is intended for medium power applications, operating from a 2.5V to 5.5V input voltage range. The device has a user-configurable operating frequency up to 4MHz, allowing the use of tiny, low cost capacitors and inductors 2mm or less in height. The output voltage is adjustable from 0.8V to 5V. Internal sychronous 0.11Ω power switches with 2.4A peak current ratings provide high effi ciency. The LTC3568’s current mode architecture and external compensation allow the transient response to be optimized over a wide range of loads and output capacitors. The LTC3568 can be confi gured for automatic power sav- ing Burst Mode operation to reduce gate charge losses when the load current drops below the level required for continuous operation. For reduced noise and RF interfer- ence, the SYNC/MODE pin can be confi gured to skip pulses or provide forced continuous operation. To further maximize battery life, the P-channel MOSFET is turned on continuously in dropout (100% duty cycle) with a low quiescent current of 60μA. In shutdown, the device draws <1μA.

File format: PDF Size:243 KB

The LTC ®2411/LTC2411-1 are 2.7V to 5.5V micropower 24-bit differential ∆Σ analog-to-digital converters with an integrated oscillator, 2ppm INL and 0.29ppm RMS noise. They use delta-sigma technology and provide single cycle settling time for multiplexed applications. Through a single pin, the LTC2411 can be configured for better than 110dB differential mode rejection at 50Hz or 60Hz ±2%, and the LTC2411-1 can provide better than 87dB input differential mode rejection over the range of 49Hz to 61.2Hz, or they can be driven by an external oscillator for a user-defined rejection frequency. The LTC2411 and LTC2411-1 are identical when driven by an external oscillator. The internal oscillator requires no external frequency setting components. The converters accept any external differential reference voltage from 0.1V to VCC for flexible ratiometric and remote sensing measurement configurations. The full- scale differential input range is from –0.5VREF to 0.5VREF. The reference common mode voltage, VREFCM, and the input common mode voltage, VINCM, may be indepen- dently set anywhere within the GND to VCC range of the LTC2411/LTC2411-1. The DC common mode input rejec- tion is better than 140dB. The LTC2411/LTC2411-1 communicate through a flexible 3-wire digital interface that is compatible with SPI and MICROWIRE TM protocols.

File format: PDF Size:1016 KB

The LTC1148 series is a family of synchronous step-down switching regulator controllers featuring automatic Burst Mode operation to maintain high efficiencies at low output currents.

File format: PDF Size:238 KB

LTC1778/LTC1778-1 1778fb No RSENSEWide Operating Range, TM Step-Down Controller is a synchronous step-down switching regulator controller without resistor, which has extremely fast transient response and stable ceramic COUT. It can be used in notebook computers and palmtop computers.

File format: PDF Size:262 KB

The LT®6013 and LT6014 are precision op amps from Linear Technology Corporation that combine low noise and high precision input performance with low power consumption and rail-to-rail output swing.

File format: PDF Size:333 KB

The LT1108 is an improved version of the LT1173, which uses a 60% duty cycle for lower power consumption and higher output current. Suitable for battery-powered systems, it can operate over a 2V to 30V voltage range and output adjustable 5V or 12V.

File format: PDF Size:231 KB