ANALOG Manuals

AD8339 is a DC to 50MHz quad I/Q demodulator and phase shifter.

The AD420 is a complete digital to current loop output converter designed to meet the needs of the industrial control market. It provides a high precision, fully integrated, low cost single-chip solution for generating current loop signals in a compact 24-lead SOIC or PDIP package. The output current range can be programmed to 4 mA–20 mA, 0 mA–20 mA or 0 mA–24 mA.

AD815 is a high output current differential driver from TI, with flexible configuration, high output power, low distortion and high speed.

ADM1033 Rev. 0 is a thermal monitor and fan speed controller with 1 local and 1 remote temperature channel. It features automatic series resistance cancellation on remote temperature channels, fast measurement rate of up to 64 measurements per second, compliance with SMBus 2.0, 1.1, and 1.0 standards, programmable over-/undertemperature limits, programmable fault queue, fan speed controller with look-up table for temperature-to-fan-speed control, and various inputs and outputs for therm and fan fault.

AD8055/AD8056 are low cost 300MHz voltage feedback amplifiers with single/dual channels, easy-to-use voltage feedback architecture, bandwidth up to 300MHz, 1400V/µs slew rate, 20ns settling to 0.1%, low distortion(-72dBc@10MHz), low noise(6nV/√Hz), low DC errors(5mV Max VOS, 1.2µA Max IB), small size(AD8055 is SOT-23-5, AD8056 is 8-Lead MSOP), excellent video specifications(RL=150Ω, G=+2), gain flatness 0.1dB to 40MHz, 0.01% differential gain error, 0.02° differential phase error, drive 4 video loads(37.5V), low power(-5V supply), 5mA typical/amplifier power supply current, high output drive current(over 60mA).

The ADM1021 is a low cost microprocessor system temperature monitor with the following features: Replacement for MAX1617; On-Chip and Remote Temperature Sensing; No Calibration Necessary; 1°C Accuracy for On-Chip Sensor; 3°C Accuracy for Remote Sensor; Programmable Conversion Rate and Delay; Support Programmable Alerts; Support Programmable Interrupts; SMBus Bus Interface.

The document describes the features and characteristics of the Analog Devices OP471, a high-speed, low-noise quad operational amplifier. It includes excellent speed, low noise, high gain bandwidth, low input offset voltage and drift, and more.

AD7143 is a programmable capacitive touch sensor controller with 8 analog input channels, providing 25ms touch update rate, resolution up to 1fF, automatic calibration and environmental compensation, integrated I2C bus interface, power supply voltage of 2.6V to 3.6V.

This datasheet provides a comprehensive overview of the features and capabilities of the ADM1062, including the 10 supply fault detectors, 5 selectable input attenuators, 5 dual-function inputs, 10 programmable output drivers, and the sequencing engine (SE).

The AD1990 is a 2-channel, bridge tied load (BTL), switching audio power amplifier with integrated Σ-Δ modulator. The modulator accepts a single-ended, analog input signal and converts it to a switching waveform to drive speakers directly. A digital, microprocessor-compatible interface provides control of reset, mute, and PGA gain, as well as feedback signals for thermal and overcurrent detection.

The AD8631/AD8632 is a single supply 1.8V to 6V, 5MHz bandwidth low power operational amplifier. It is available in SOT-23 and SOIC packaging.

The ADG1204 is a low capacitance, low charge injection, ±15 V/+12 V 4:1 iCMOS™ Multiplexer, featuring 1.5 pF off source capacitance and <1 pC charge injection, and is suitable for use in automatic test equipment, data acquisition systems, battery-powered systems, sample-and-hold systems, audio signal routing, video signal routing and communication systems.

The ADT7476A is a dBCOOL controller that can monitor up to five voltages, control and monitor up to four fans, and has high and low frequency fan drive signals. It has an on-chip temperature sensor, two remote temperature sensors, a temperature measurement range of up to 191°C, an automatic fan speed control mode that controls system cooling based on the measured temperature, an enhanced acoustic mode that significantly reduces user perception of changing fan speeds, a thermal protection feature via the THERM output, monitoring of the performance impact of the Intel® Pentium® 4 processor, a thermal control circuit via the THERM input, support for 3-wire and 4-wire fan speed measurement, and limit comparison of all monitored values. All TACH and PWM channels support 5V, and meet the SMBus 2.0 electrical specifications.

The AD9857 is a 200 MHz 14-bit digital upconverter produced by Analog Devices. It has a 4× to 20× programmable reference clock multiplier, an internal 32-bit quadrature DDS, FSK function, 8-bit output amplitude control, a single pin power-down function, four programmable, pin-selectable signal profiles, SIN(x)/x correction (inverse SINC function), a simplified control interface, 10 MHz serial, 2-wire or 3-wire SPI compatible, 3.3 V single supply, single-ended or differential input reference clock, 80-lead LQFP surface-mount packaging, three modes of operation: quadrature modulator mode, single-tone mode, interpolating DAC mode, and is mainly used in HFC data, telephony and video modems, wireless base station, Agile, L-Band satellite communication and other applications.