ANALOG Manuals

This document describes the AD7938/AD7939, an 8-channel, 1.5 MSPS, 12-bit and 10-bit parallel ADC. It features configurable analog input channels, accurate on-chip 2.5V reference, and a high-speed parallel interface.

The AD7490 is a 12-bit high speed, low power, 16-channel, successive-approximation ADC. The part operates from a single 2.7 V to 5.25 V power supply and features throughput rates up to 1 MSPS. The part contains a low noise, wide bandwidth tra

AD7366-5/AD7367-5 is a 12/14-bit dual-channel analog-to-digital converter (ADC) from Analog Devices. It features multiple programmable input ranges of ±10V, ±5V, 0V to +10V, and ±12V with a +3V external reference, a conversion rate of up to 500kSPS, high analog input impedance, and low power consumption.

The ADAU1702 is a 28-bit/56-bit audio processor with two ADCs and four DACs. It has a processing power of 25 MIPS, two ADCs with 100 dB SNR and -83 dB THD+N, and four DACs with 104 dB SNR and -90 dB THD+N. The device has a fully standalone operating mode and can be self-booted from a serial EEPROM. It also features an auxiliary ADC, GPIOs, and a programmable SigmaStudio™ graphical tool.

The AD8132 is a low cost, high speed differential amplifier with resistor settable gain. The AD8132 is a major advancement over op amps for driving differential input ADCs or for driving signals with fast rise times.

This document describes the features and characteristics of the ADV7174/ADV7179 chip scale PAL/NTSC video encoder, including ITU-R1 BT601/BT656 YCrCb to PAL/NTSC video encoder, high quality 10-bit video DACs, advanced power management features, etc.

The AD598 is a complete, monolithic Linear Variable Differential Transformer (LVDT) signal conditioning subsystem. It is used in conjunction with LVDTs to convert transducer mechanical position to a unipolar or bipolar dc voltage with a high degree of accuracy and repeatability. All circuit functions are included on the chip. With the addition of a few external passive components to set frequency and gain, the AD598 converts the raw LVDT secondary output to a scaled dc signal. The device can also be used with RVDT transducers.

The AD5930 is a programmable frequency sweep and output burst waveform generator. It features a programmable frequency profile, no external components necessary, output frequency up to 25 MHz, burst and listen capability, preprogrammable frequency profile minimizes number of DSP/µcontroller writes, sinusoidal/triangular/square wave outputs, automatic or single pin control of frequency stepping, waveform starts at known phase, increments at 0° phase or phase continuously, power-down mode: 20 µA, power supply: 2.3 V to 5.5 V, automotive temperature range: −40°C to +125°C, 20-lead pb-free TSSOP. It is suitable for frequency sweeping/radar, network/impedance measurements, incremental frequency stimulus, sensory applications, proximity and motion, BFSK frequency bursting/pulse trains, etc.

AD7357 is a dual 14-bit SAR ADC with a maximum conversion rate of 4.2 MSPS and a 2.5 V supply voltage. It is packaged in a 16-lead TSSOP.

AD8510/AD8512/AD8513 are low noise, low input bias current, wide bandwidth JFET operational amplifiers produced by Analog Devices

The AD5441 is a 12-bit multiplying digital-to-analog converter with serial input. It features excellent analog performance and is ideal for applications where PC board space is limited.

The OP270 is a high performance, monolithic, dual operational amplifier with exceptionally low voltage noise, 5 nV/÷Hz max at 1 kHz. It offers comparable performance to ADI’s industry standard OP27. The OP270 features an input offset voltage below 75 mV and an offset drift under 1 mV/∞C, guaranteed over the full military tem- perature range. Open-loop gain of the OP270 is over 1,500,000 into a 10 kW load, ensuring excellent gain accuracy and linearity.

AD2S1205 is a 12-bit R/D converter with reference oscillator

AD9833 is a low power 20mW 2.3V to 5.5V programmable waveform generator.