Key facts
- Manuals
- 3
- Languages
- ZH · EN
- Last added
- 2026-10-03
Featured S&T manuals
ST STM32 PMSM FOC SDK v4.2 Three-Phase Motor Control Solution and Applications
The STM32 PMSM FOC SDK v4.2 provides a complete motor‑control software development kit for three‑phase permanent‑magnet synchronous motors. It includes a firmware library, Motor Profiler analysis tool, the ST MC Workbench PC graphical interface, and a toolbox of utilities and expansion boards to accelerate development.
The SDK is demonstrated in a variety of applications, ranging from gimbal stabilization, 3D printing, electric bicycles, to household appliances like air‑conditioners and refrigerators. It supports a wide range of STM32 microcontrollers and offers hardware platforms such as X‑NUCLEO expansion boards and SLLIMM power cards. This manual is written in Chinese.
Covers: Overview · Firmware Library · Motor Profiler · ST MC Workbench PC GUI · Application Examples · Supported STM32 MCUs
ST ST7565 LCD Controller/Driver Datasheet
The ST7565 is a single‑chip dot‑matrix LCD controller/driver that can be connected directly to an 8‑bit or 16‑bit microprocessor bus. It provides 65 × 132 bits of display RAM (8580 bits) and supports both parallel and serial interfaces. The device includes built‑in power‑supply circuits, voltage regulators and a low‑power LCD driver, enabling operation from a 4.0 V to 5.5 V logic supply.
The document details pin dimensions, electrical characteristics, timing diagrams, power‑supply pin functions and reset timing. It also lists revision history and mechanical drawing data for the chip package.
Covers: General Description · Pin Dimensions · Pin Descriptions · Power Supply Pins · System Bus Connection Pins · Timing
ST ST-LINK/ST-LINK v2/ST-LINK ISOL Programmer Debugger User Manual
The ST‑LINK, ST‑LINK v2 and ST‑LINK ISOL are on‑board emulators and programmers for STM8 and STM32 microcontrollers. They communicate via USB full‑speed and support JTAG/SWD as well as SWIM interfaces, allowing debugging and programming of a wide voltage range.
The manual describes basic features, hardware configuration, connector pin definitions, required drivers and software, and includes revision history. It also provides guidance on connecting the device to target boards and obtaining the necessary ST software from the STMicroelectronics website. This manual is written in Chinese.
Covers: Introduction · Basic Features · Hardware Configuration · Connector Signal Definition · Software and Drivers · Revision History
Latest S&T manuals
ST STM32 PMSM FOC SDK v4.2 Three-Phase Motor Control Solution and Applications
Application Note 28 pages · 2.1 MB · ZHThis ST document presents the STM32 PMSM FOC SDK v4.2, covering firmware, motor profiler, PC GUI tools, and example applications such as gimbals, 3D…
ST ST7565 LCD Controller/Driver Datasheet
Datasheet 56 pages · 463 KB · ENTechnical datasheet for the ST7565 65 × 132 dot‑matrix LCD controller/driver covering specifications, pinout and timing.
ST ST-LINK/ST-LINK v2/ST-LINK ISOL Programmer Debugger User Manual
User Manual 4 pages · 1.5 MB · ZHUser manual for the ST‑LINK series debugger/programmer covering features, hardware, connectors and software setup.
Which document do I need?
Application Note
How to use the product for one specific task, with worked examples.
Datasheet
Ratings, dimensions and ordering codes, for selection and design work.
User Manual
Day-to-day operation, settings and troubleshooting. Start here if the product is already set up.
Questions answered in S&T manuals
What is the display RAM capacity of the ST7565?
The ST7565 provides 65 × 132 bits of display RAM, which equals 8580 bits.
What voltage range does the ST7565 operate on?
It operates from a logic power supply of 4.0 V to 5.5 V.
Do I need to install drivers for the ST‑LINK v2?
Yes, the ST‑LINK v2 uses the WinUSB driver and requires the USB driver to be installed.
From: ST ST-LINK/ST-LINK v2/ST-LINK ISOL Programmer Debugger User Manual
What is the operating temperature range of the device?
The device operates from 0 °C up to 50 °C.
From: ST ST-LINK/ST-LINK v2/ST-LINK ISOL Programmer Debugger User Manual