ST Manuals

SPIRIT1 is a low-data-rate, low-power sub-1GHz transceiver that supports 2-FSK, GFSK, MSK, GMSK, OOK and ASK modulation schemes, air data rates from 1 to 500 kbps, has excellent receiver sensitivity (-120 dBm), selectivity and blocking characteristics, very low power consumption (RX is 9 mA, TX is 21 mA, transmit power is programmable up to +11 dBm), fast start-up, and short frequency synthesizer settling time (6 µs), and has frequency offset compensation, integrated temperature sensor, battery indicator and low battery detector, RX and TX FIFO buffer (each 96 bytes), configurability via SPI interface, automatic acknowledgement, retransmission and timeout protocol engine, AES 128-bit encryption co-processor, antenna diversity algorithm, fully integrated ultra low power RC oscillator, internal timer wake-up and wake-up on external event, flexible packet length with dynamic payload length, sync word detection, address check, automatic CRC handling, FEC with interleaving, digital RSSI output, programmable carrier sense (CS) indicator, automatic clear channel assessment (CCA) before transmitting (for ISM band).

ST7580 is the STMicroelectronics company's FSK, PSK multi-mode system-on-chip for power line communication, which has a high-performance PHY processor and protocol engine, supports B-FSK, B-PSK, Q-PSK, 8-PSK modulation, dual channel operation mode, convolutional error correction coding, signal-to-noise ratio estimation, PNA mode against impulsive noise.

This document describes the features and characteristics of 2.4 GHz IEEE 802.15.4-compliant SMD modules based on the STM32W chipset, including integrated 2.4 GHz transceiver, ARM Cortex-M3 core, 128 kB embedded Flash, and 8 kB embedded RAM.

STW82103B is an integrated down converter providing 8 dB of gain, 10.5 dB NF, and a very high input linearity by means of its passive mixer. Embedding two wide band automatic center frequency calibration differential VCOs, dual modulus programmable prescaler (16/17 or 19/20), programmable reference frequency divider (10 bits), adjustable charge pump current, digital lock detector and fast lock time (150 µs).

STW82102B RF down converter with embedded integer-N synthesizer

This datasheet provides comprehensive information on STMicroelectronics STW82101B RF down converter. The device provides 8.5 dB of gain, 9.5 dB NF, and a very high input linearity by means of its passive mixer. It also integrates two wide band automatic center frequency calibrated differential VCOs operating in the 850 to 1025 MHz and 1025 to 1185 MHz frequency bands. The device also integrates an integer-N synthesizer featuring a dual modulus programmable prescaler (16/17 or 19/20), a programmable reference frequency divider (10 bits), an adjustable charge pump current, a digital lock detector, excellent integrated phase noise, and a fast lock time (150 µs). The device also integrates a DAC with dual current outputs. The device features a 3.3 V and 5 V analog supply, a 3.3 V digital supply, and provides SPI and I2C bus interfaces (fast mode) with a 3 bit programmable address (1101A2A1A0).

The STMicroelectronics STW82100B is an integrated down converter providing 8 dB of gain, 10.5 dB NF, and a very high input linearity by means of its passive mixer.

The ST7570 is a powerful power line networking system-on-chip. It combines a fully integrated narrow-band power line networking system-on-chip with a high-performing PHY processor and embedded turn-key firmware for spread-frequency shift keying (S-FSK) modulation. It supports programmable bit rate and carriers, signal to noise ratio estimation, received signal strength indication, and protocol engine embedding. The chip also features on chip peripherals like UART interface, fully integrated analog front end with ADC, DAC, and PGA, as well as a single-ended power amplifier. It is suitable for smart metering applications, street lighting control, and command and control networking.

The SPZB260C-PRO is a low power, compact ZigBee® module optimized for embedded applications. It enables OEMs to easily add wireless capability to electronic devices. The module is based on the EM260 ZigBee network processor, which integrates a 2.4 GHz IEEE 802.15.4 compliant transceiver and IEEE 802.15.4 PHY and MAC. A single supply voltage is required to power the module. The voltage supply also determines the I/O port level, allowing easy integration with the target device. The module integrates an RF UFL connector, allowing the use of an external antenna.

This document is about the SPBT2532C2.AT module, which is a micro-sized Bluetooth module with high performance. It supports Bluetooth 2.1 protocol, output power class 2, transmission speed up to 2Mbps. It supports various communication interfaces, including UART, I/O, etc.

SPZB260-PRO is a low power consumption ZigBee® module optimized for embedded applications. It enables OEMs to easily add wireless capability to electronic devices. The module is based on SN260 ZigBee® network processor which integrates a 2.4 GHz, IEEE 802.15.4-compliant transceiver as well as IEEE 802.15.4 PHY and MAC. 24 MHz high stability crystal is integrated in the module to perform the timing requirements as per ZigBee.

The TN100 is a high-performance CSS transceiver with location awareness capability. It is a single-chip solution for ISM 2.45 GHz RF transceiver, with built-in ranging capability for link distance estimation. It supports modulation technique: chirp spread spectrum (CSS), FDMA support: 7 channels, 3 non-overlapping, and data rates: 2 and 1 Mbps; 500, 250 and 125 kbps. It has adjustable output power and high precision ranging capability, supports external power amplifier to increase output power. The supply voltage range is from 2.3 V to 2.7 V, and it operates in an industrial temperature range from -40°C to +85°C.

This is a 350-400MHz FSK/ASK receiver that has multichannel, high dynamic range, PLL and VCO integration, image rejection mixer integration, Start Code Detector block (SCD), I2C serial interface, etc.

SPZB250 is a low power consumption ZigBee module based on EM250 ZigBee system-on-chip which integrates a 16-bit processor together with a 2.4 GHz, IEEE 802.15.4-compliant transceiver as well as IEEE 802.15.4 PHY and MAC. It enables OEMs to easily add wireless networking capability to any electronic device. Such a module is a very comprehensive solution to build wireless sensors with meshing and self-healing capability as required in a WSN scenario.