Philips Manuals (Others)

This document is a specification sheet for Philips SAA1310 control interface chip, which provides information such as the chip's functions, pin definitions, and package forms.

File format: PDF Size:111 KB

SAA1305T is an on/off logic IC intended for use in car radios to interface between a microcontroller and various input signals such as ignition, low supply detection, on/off key and external control signals.

File format: PDF Size:181 KB

This document is about SAA1300, SAA1300 is a switch circuit that is used to turn on and off the power lines of various circuit parts via an I2C bus signal. It can also be used to supply current for switching diodes in radio and television tuners. It contains 5 output stages, which are capable of supplying up to 85 mA in the ON state or sinking up to −100 µA in the OFF state. Current limiting and short-circuit protection are included. The output stages are driven by a shift register/latch combination which is loaded via data from the I2C bus. A power-on reset of the latches ensures the OFF state of the output stages (OUT 2 to OUT 5) without data reception from the I2C bus. A subaddressing system allows the connection of up to three circuits on the same I2C bus lines; one of the outputs (OUT 1, pin 7) can also be used as an input to select the device via a simple internal A/D converter.

File format: PDF Size:40 KB

The SAA1101 is a Universal Sync Generator (USG) from Philips and is designed for use in video sources such as cameras, film scanners, video generators and associated apparatus. The circuit can be considered as a successor to the SAA1043 sync generator and the SAA1044 subcarrier coupling IC.

File format: PDF Size:118 KB

TJ1054A is a fault-tolerant CAN transceiver, which is used in automotive bus communication. It supports up to 32 nodes with a maximum transmission speed of 125kBaud.

File format: PDF Size:115 KB

This document describes the features of TJA1054 fault-tolerant CAN transceiver, including optimized for in-car low-speed communication, support for multiple node connections, support for unshielded bus wires, very low Radio Frequency Interference (RFI), fully integrated receiver filters, bus failure management, protection features, and support for low power modes.

File format: PDF Size:131 KB

This document describes the features and characteristics of the TJA1050 high speed CAN transceiver, including full compatibility with the ISO 11898 standard, high speed transmission rate, transmit data dominant time-out function, transient protection in automotive environment, silent mode, differential receiver with wide common-mode range for high electromagnetic immunity, input levels compatible with 3.3V devices, thermal protection, short-circuit proof to battery and ground, and non-disturbance of bus lines by unpowered nodes.

File format: PDF Size:81 KB

TJ1053 is a CAN bus controller interface chip launched by Philips Semiconductors. It is mainly used for low-speed automotive bus communication applications, which can support up to 125kbps baud rate and connect up to 32 nodes.

File format: PDF Size:119 KB

TJA1040 is a high speed CAN transceiver for automotive applications, with high speed (up to 1 MBaud), very low standby current and remote wake-up capability via the bus.

File format: PDF Size:88 KB

The TJA1020 LIN transceiver is a low power, high performance interface for Local Interconnect Network (LIN). It supports baud rates up to 20 kbit/s. The device includes an integrated termination resistor for connection from either 3.3 V or 5 V devices. The TJA1020 also features a low slope mode for further reduction of EME.

File format: PDF Size:103 KB

BF991 is a N-channel dual-gate MOS-FET produced by Philips company. Its features are overvoltage protection, and it is used in VHF television tuners and FM tuners.

File format: PDF Size:39 KB

BF992 is a N-channel dual gate MOS-FET produced by Philips. It is suitable for applications such as VHF television tuners and FM tuners with 12V supply voltage.

File format: PDF Size:67 KB

The BF990A is an N-channel dual-gate MOS-FET with integrated back-to-back diodes to protect against excessive input voltage surges. It is suitable for RF applications such as television tuners with a 12V supply voltage and professional communication equipment.

File format: PDF Size:66 KB

BF989 is a N-channel dual-gate MOS-FET produced by Philips. It has protection against excessive input voltage surges and is used in UHF television tuners and professional communication equipment.

File format: PDF Size:62 KB

File format: PDF Size:298 KB

This document is the data sheet for PCF2113x LCD controllers/drivers, describing the features and characteristics of the products.

File format: PDF Size:365 KB

This document is about the product specification of PCF2105 LCD controller/driver. It describes the features, applications, general description, ordering information, pinning, functional description, instructions, and other details of the product.

File format: PDF Size:302 KB

PCF2104x is an LCD controller/driver with various functions and features, suitable for various applications.

File format: PDF Size:261 KB

This document is a Philips Semiconductors product specification of PCF2103 family LCD controllers/drivers. It describes the features, applications, functional description, interface, instructions, etc. of the product in detail.

File format: PDF Size:227 KB

This document is the specification sheet of the PCF2103 family LCD controllers/drivers, introducing the features and characteristics of the products in the series.

File format: PDF Size:227 KB