NXP sensor Manuals

The NXP Semiconductors SA56004X is an SMBus compatible, 11-bit remote/local digital temperature sensor with overtemperature alarms. The remote channel of the SA56004X monitors a diode junction, such as a substrate PNP of a microprocessor or a diode connected transistor such as the 2N3904 (NPN) or 2N3906 (PNP). With factory trimming, remote sensor accuracy of 1 C is achieved.

File format: PDF Size:562 KB

PCA8885 is an 8-channel touch sensor chip produced by NXP. It uses EDISEN technology to automatically compensate for static capacitance changes

File format: PDF Size:837 KB

The integrated circuit PCF8885 is a capacitive 8-channel touch and proximity sensor that uses a patented (EDISEN) method to detect a change in capacitance on remote sensing plates. Changes in the static capacitances (as opposed to dynamic capacitance changes) are automatically compensated using continuous auto-calibration. Remote sensing plates (for example, conductive foils) can be connected to the IC1 using coaxial cable. The eight input channels operate independently of each other. There is a

File format: PDF Size:405 KB

The integrated circuit PCF8883 is a capacitive touch and proximity switch that uses a patented (EDISEN) digital method to detect a change in capacitance on a remote sensing plate. Changes in the static capacitance (as opposed to dynamic capacitance changes) are automatically compensated using continuous auto-calibration. Remote sensing plates (e.g. conductive foil) can be connected directly to the IC1 or remotely using a coaxial cable.

File format: PDF Size:315 KB

The PCT2075 also includes an open-drain output (OS) which becomes active when the temperature exceeds the programmed limits. The OS output operates in either of two selectable modes: OS comparator mode or OS interrupt mode. Its active state can be selected as either HIGH or LOW. The fault queue that defines the number of consecutive faults in order to activate the OS output is programmable as well as the set-point limits.

File format: PDF Size:1688 KB

This datasheet introduces the basic information of NXP PCA8886 sensor. It is a low power dual channel capacitive proximity switch that uses a patented EDISEN digital method to detect a change in capacitance on remote sensing plates. Static capacitance (i.e. non-dynamic capacitance changes) are automatically compensated by continuous auto-calibration. Remote sensing plates (e.g. conductive foil) can be connected directly to the IC1 or remotely using a coaxial cable.

File format: PDF Size:268 KB

The KMZ60 angle sensor is dedicated for rotor position detection for BLDC motors.Beyond that the KMZ60 is applicable for Electronic Power Steering (EPS) applications,steering angle measurement, window wiper position detection and general contactless angular measurement (e.g. throttle valves or actuators). The KMZ60 is fully automotive qualified as well as applicable for industrial and consumer applications.

File format: PDF Size:1322 KB

The KMA220 is a dual channel magnetic angle sensor module. The MagnetoResistive (MR) sensor bridges, the mixed signal Integrated Circuits (ICs) and the required capacitors are integrated into a single package. Both integrated channels are working full independently. The supply voltage has common terminals. Further explanations are referring to a single channel of the KMA220.

File format: PDF Size:730 KB

The KMA215 is a magnetic angle sensor module with digital output in accordance with SAE J2716 JAN2010 Single Edge Nibble Transmission (SENT). The MagnetoResistive (MR) sensor bridges, the mixed signal Integrated Circuit (IC) and the required capacitors are integrated into a single package.

File format: PDF Size:480 KB

The KMA221 is a magnetic angle sensor module. The MagnetoResistive (MR) sensor bridges, the mixed signal Integrated Circuit (IC) and the required capacitors are integrated into a single package.

File format: PDF Size:546 KB

The LM75B can be configured for different operation conditions. It can be set in normal mode to periodically monitor the ambient temperature, or in shutdown mode to minimize power consumption. The OS output operates in either of two selectable modes:OS comparator mode or OS interrupt mode. Its active state can be selected as either HIGH or LOW. The fault queue that defines the number of consecutive faults in order to activate the OS output is programmable as well as the set-point limits.

File format: PDF Size:565 KB

This document describes design aspects which should be considered for application circuits using NXP capacitive sensors.

File format: PDF Size:618 KB

This application note will illustrate the new features of the LPC11U6x device family compared to the LPC11U3x device family.

File format: PDF Size:210 KB

This application note is related to the installation procedures of the PTEV501B Board. It describes the board and the required actions to hand on quickly the Evaluation board.

File format: PDF Size:1503 KB

This application note explains the unique auto-calibration feature of the touch sensor family from NXP and provides guidelines for enhanced water and condensation safe operation, focusing on applications with capacitive touch buttons

File format: PDF Size:771 KB

This document provides information regarding the migration from the EM773 to the EM783-SC version device. This document should be used in conjunction with both device datasheets. The following is a list of the differences between EM773 and EM783-SC.

File format: PDF Size:93 KB

NXP Semiconductors

File format: PDF Size:312 KB

This application note describes briefly important factors for the usage of the PCF8883 and PCA8886 sensor devices.

File format: PDF Size:225 KB