ANALOG Manuals (Industrial)

AD22105 is a low voltage, resistor programmable thermostatic switch with user-programmable temperature setpoint, wide supply range, wide temperature range, etc. It is suitable for applications such as industrial process control, thermal control systems, CPU monitoring, computer thermal management circuits, fan control, handheld/portable electronic equipment, etc.

File format: PDF Size:263 KB

File format: PDF Size:957 KB

The AD8131 is a high performance, low cost differential driver with 400 MHz bandwidth, 2000 V/µs slew rate and 2 fixed gain, which can be used for video line driver, digital line driver, low power differential ADC driver etc.

File format: PDF Size:373 KB

The AD8324 is a low cost amplifier designed for coaxial line driving. The features and specifications make the AD8324 ideally suited for DOCSIS 2.0 and Euro-DOCSIS applications. The gain of the AD8324 is digitally controlled in 1 dB steps over a 59 dB range. Low distortion at 61 dBmV output: -59 dBc SFDR@21 MHz, -54 dBc SFDR@65 MHz. Output noise level @ minimum gain 1.3 nV/√Hz. Maintains 75 Ω output impedance in TX-enable and Transmit-disable condition. Upper bandwidth: 100 MHz (full gain range). Supports SPI® interfaces.

File format: PDF Size:319 KB

The document describes the features and characteristics of the AD8139 differential ADC driver, including low noise, rail-to-rail operation, differential input and output, and high speed.

File format: PDF Size:679 KB

AD8134 is a three-way differential driver from Analog Devices, it uses Sync-On-Common-Mode technology, it has 225 MHz, -3 dB large signal bandwidth and 450 MHz, -3 dB small signal bandwidth. AD8134 can easily drive 1.4 V p-p video signal into doubly terminated 100 Ω UTP cable.

File format: PDF Size:449 KB

AD8133 Rev. 0 is a triple differential driver with output pull-down feature. It features high speed, low distortion, low power consumption, and is suitable for applications such as KVM networking and UTP.

File format: PDF Size:480 KB

The ADA4302-4 is an active RF splitter used in applications where a lossless signal split is required. It features a single 5V supply, 54MHz to 865MHz CATV operating range, 4.6dB gain per output channel, 4.4dB noise figure, 25dB isolation between output channels, etc.

File format: PDF Size:225 KB

The AD8337 is a low noise, single-ended, linear-in-dB, general-purpose variable gain amplifier (VGA) usable for video, imaging, medical imaging, industrial radar, and other applications. It features low noise, wide bandwidth, low power, single-ended input and output, and high speed uncommitted op amp input, making it suitable for a variety of applications.

File format: PDF Size:1088 KB

AD8143 is a high-speed, triple differential receiver with comparators. It features a large signal bandwidth of 160 MHz, slew rate of 1000 V/μs, high CMRR of 65 dB, and a differential input impedance of 5 MΩ.

File format: PDF Size:569 KB

This document describes the features of Analog Devices' AD8331/AD8332/AD8334 series ultralow noise variable gain amplifiers (VGAs) with preamplifier. The features include ultralow noise, wide gain range, low power consumption, and applications such as ultrasound and sonar time-gain controls, high performance automatic gain control systems, and I/Q signal processing.

File format: PDF Size:1819 KB

The ADA4303-2 is a 75 Ω, two-output active splitter for use in applications where a lossless split is required. It features excellent frequency response and low noise characteristics, making it ideal for CATV applications.

File format: PDF Size:259 KB

The AD8392A is a low power, high output current, quad op amp designed for use as an ADSL/ADSL2+ line driver. It features four current feedback, high current amplifiers, low power operation, multiple power supply modes, high output voltage and current drive, low distortion, and high speed capabilities.

File format: PDF Size:547 KB

The AD8336 is a low noise, wide bandwidth, DC-coupled VGA amplifier with ±3V to ±12V supply voltage and -55°C to +125°C temperature range. The device features 3nV/√Hz low voltage noise and 3pA/√Hz low current noise.

File format: PDF Size:789 KB

This document is a detailed introduction of ADL5570 WiMAX power amplifier, including its features, applications and application guides.

File format: PDF Size:348 KB

The AD8398 is a VDSL dual line driver with shutdown. It features wide output swing, high output current, low distortion and high speed. AD8398 can be used for VDSL line drivers, consumer xDSL modems and twisted pair line drivers etc.

File format: PDF Size:90 KB

The ADA4937-x is a low noise, ultralow distortion, high speed differential amplifier. It is an ideal ADC driver and can be used in applications such as single-ended-to-differential converters, IF and baseband gain blocks, differential buffers, and line drivers.

File format: PDF Size:567 KB

The ADA4304-3/ADA4304-4 is a 1:3 and 1:4 single-ended, low cost, active RF splitter.

File format: PDF Size:432 KB

AD8394 is a low power, high output current, quad op amp, ideal for use as ADSL/ADSL2+ dual-channel, central office (CO) line drivers. It supports dual-supply operation from ±6 V to ±12 V, single-supply operation from 12 V to 24 V, and has an internal power dissipation of 700 mW while driving a 20.4 dBm ADSL2+ signal (CF = 5.5). It also features a low output impedance, high output voltage and current drive, and low distortion MTPR down to −70 dBc. The AD8394 is ideal for applications such as ADSL/ADSL2+ CO line drivers, xDSL line drivers, high output current, low distortion amplifiers, and DAC output buffers.

File format: PDF Size:62 KB

The ADL5571 is a high linearity 2.5GHz to 2.7GHz power amplifier designed for WiMAX mobile terminals and CPEs using TDD operation at a duty cycle of 50% or lower.

File format: PDF Size:463 KB