ANALOG Manuals

This document describes the features and characteristics of the AD8330 variable gain amplifier. It has a fully differential signal path, which can also be used with single-sided signals. The input range is from 0.3mV to 1V rms, and the output is in rail-to-rail mode. It also has automatic offset compensation, linear-in-dB and linear-in-magnitude gain modes. The gain range is from 0dB to 50dB, with an inverted gain range of 50dB to 0dB. The nominal gain range is from 0.03 to 10, with a magnitude range of 15mV to 5V. It has a constant bandwidth of 150MHz, low noise, low distortion, and low power consumption. It is suitable for applications such as pre-ADC signal conditioning and driving adjustable AGC amplifiers.

File format: PDF Size:944 KB

The AD8324 is a low cost amplifier designed for coaxial line driving. The features and specifications make the AD8324 ideally suited for DOCSIS 2.0 and Euro-DOCSIS applications. The gain of the AD8324 is digitally controlled in 1 dB steps over a 59 dB range. Low distortion at 61 dBmV output: -59 dBc SFDR@21 MHz, -54 dBc SFDR@65 MHz. Output noise level @ minimum gain 1.3 nV/√Hz. Maintains 75 Ω output impedance in TX-enable and Transmit-disable condition. Upper bandwidth: 100 MHz (full gain range). Supports SPI® interfaces.

File format: PDF Size:319 KB

The document describes the features and characteristics of the AD8139 differential ADC driver, including low noise, rail-to-rail operation, differential input and output, and high speed.

File format: PDF Size:679 KB

File format: PDF Size:0 KB

AD8134 is a three-way differential driver from Analog Devices, it uses Sync-On-Common-Mode technology, it has 225 MHz, -3 dB large signal bandwidth and 450 MHz, -3 dB small signal bandwidth. AD8134 can easily drive 1.4 V p-p video signal into doubly terminated 100 Ω UTP cable.

File format: PDF Size:449 KB

AD8133 Rev. 0 is a triple differential driver with output pull-down feature. It features high speed, low distortion, low power consumption, and is suitable for applications such as KVM networking and UTP.

File format: PDF Size:480 KB

The ADA4302-4 is an active RF splitter used in applications where a lossless signal split is required. It features a single 5V supply, 54MHz to 865MHz CATV operating range, 4.6dB gain per output channel, 4.4dB noise figure, 25dB isolation between output channels, etc.

File format: PDF Size:225 KB

This product is a high voltage, differential 18-bit ADC driver. The product features include single-ended to differential conversion, low distortion, low differential output referred noise, high input impedance, fixed gain of 2, low output-referred offset voltage, low input bias current, wide supply range, high speed, fast settling time, and is available in space-saving, thermally enhanced packages.

File format: PDF Size:419 KB

The AD8337 is a low noise, single-ended, linear-in-dB, general-purpose variable gain amplifier (VGA) usable for video, imaging, medical imaging, industrial radar, and other applications. It features low noise, wide bandwidth, low power, single-ended input and output, and high speed uncommitted op amp input, making it suitable for a variety of applications.

File format: PDF Size:1088 KB

AD8143 is a high-speed, triple differential receiver with comparators. It features a large signal bandwidth of 160 MHz, slew rate of 1000 V/μs, high CMRR of 65 dB, and a differential input impedance of 5 MΩ.

File format: PDF Size:569 KB

AD8128 is a CAT-5 receiver with adjustable line equalization. It features compensation for CAT-5 cable losses, high frequency peaking adjustment, and broadband gain adjustment.

File format: PDF Size:306 KB

The ADA4941-1 is a low-power, single-supply, 18-bit ADC driver that converts single-ended input signals to differential output signals. It features excellent linearity, low noise, high input impedance, user-adjustable gain, high speed, fast settling time, low output offset, and a disable feature.

File format: PDF Size:494 KB

This document describes the features of Analog Devices' AD8331/AD8332/AD8334 series ultralow noise variable gain amplifiers (VGAs) with preamplifier. The features include ultralow noise, wide gain range, low power consumption, and applications such as ultrasound and sonar time-gain controls, high performance automatic gain control systems, and I/Q signal processing.

File format: PDF Size:1819 KB

The ADA4303-2 is a 75 Ω, two-output active splitter for use in applications where a lossless split is required. It features excellent frequency response and low noise characteristics, making it ideal for CATV applications.

File format: PDF Size:259 KB

The AD8392A is a low power, high output current, quad op amp designed for use as an ADSL/ADSL2+ line driver. It features four current feedback, high current amplifiers, low power operation, multiple power supply modes, high output voltage and current drive, low distortion, and high speed capabilities.

File format: PDF Size:547 KB

The AD8336 is a low noise, wide bandwidth, DC-coupled VGA amplifier with ±3V to ±12V supply voltage and -55°C to +125°C temperature range. The device features 3nV/√Hz low voltage noise and 3pA/√Hz low current noise.

File format: PDF Size:789 KB

AD8145 is a high-speed differential receiver with comparator function from Analog Devices. It has a speed of 500 MHz, 2000 V/μs of fast response, 0.1 dB of flatness, 69 dB of CMRR, 1MΩ input impedance, ±3.5V input voltage range, 15 ns of fast settling time, 13nV/√Hz of input noise, and a small 32-lead package. It is suitable for RGB video receivers, YPbPr video receivers, keyboard, video, mouse (KVM) receivers, unshielded twisted pair (UTP) receivers, automotive driver assistance (AD8145W) and automotive infotainment (AD8145W) applications.

File format: PDF Size:458 KB

The ADA4304-2 is a single-ended, low-cost, active RF splitter ideal for CATV and terrestrial applications. It features excellent frequency response, low noise figure, and low distortion.

File format: PDF Size:406 KB

This document describes the features and characteristics of the AD8146/AD8147/AD8148 wideband video triple differential drivers, including high-speed fully differential drivers, bandwidth, slew rate, gain, input-output configuration, output balance error, low power consumption, etc.

File format: PDF Size:446 KB

This document is a detailed introduction of ADL5570 WiMAX power amplifier, including its features, applications and application guides.

File format: PDF Size:348 KB