Linear Technology manuals, page 51
LINEAR TECHNOLOGY LT1640AL/LT1640AH Manual
The LT ®1640AL/LT1640AH are 8-pin, negative voltage Hot Swap TM controllers that allow a board to be safely inserted and removed from a live backplane
LINEAR TECHNOLOGY LT1956/LT1956-5 Manual
High Voltage, 1.5A, 500kHz Step-Down Switching Regulators
LINEAR TECHNOLOGY LTC1235 Manual
The LTC1235 is a microprocessor supervisory circuit provides complete power supply monitoring and battery control functions for microprocessor reset, battery backup, RAM write protection, power failure warning and watchdog timing.
LINEAR TECHNOLOGY LTC3703 Manual
The LTC3703 is a synchronous step-down switching regulator controller that can directly step down voltages from up to 100V, making it ideal for telecom and automotive applications. It drives external N-channel MOSFETs using a constant frequency (up to 600kHz), voltage mode architecture. A precise internal reference provides 1% DC accuracy. It has a high bandwidth error amplifier and patented line feed-forward compensation for fast line and load transient response. The LTC3703 has strong 1Ω gate drivers for higher current applications. The operating frequency is user programmable from 100kHz to 600kHz and can be synchronized to an external clock for noise-sensitive applications. Current limit is programmable with an external resistor and utilizes the voltage drop across the synchronous MOSFET to eliminate the need for a current sense resistor. For applications requiring up to 60V operation with logic-level MOSFETs, refer to the LTC3703-5 data sheet.
LINEAR TECHNOLOGY LTC1257 Manual(1)
The LTC1257 is a complete single supply, 12-bit voltage output D/A converter (DAC) in an SO-8 package from Linear Technology Corporation. The LTC1257 includes an output buffer amplifier, 2.048V voltage reference and an easy to use three-wire cascadable serial interface. An external reference can be used to override the internal reference and extend the output voltage range to 12V. The power supply current is a low 350µA when operating from a 5V supply, making the LTC1257 ideal for battery-powered applications. The space-saving 8-pin SO package and operation with no external components provide the smallest 12-bit D/A system available.
LINEAR TECHNOLOGY LTC4100 Manual
The LTC4100 is a single chip intelligent battery charger controller from Infineon that supports SMBus protocol and can communicate with the host. The LTC4100 supports a voltage range of 3.5V to 26V, and the charging current can reach 4A, with charging accuracy of up to ±0.8%.
LINEAR TECHNOLOGY LT1078/LT1079 10789fe Micropower Dual Quad Single Supply Precision Op Amps handbook
1 LT1078/LT1079 10789fe Micropower, Dual and Quad, Single Supply, Precision Op Amps is a micropower, dual and quad, single supply, precision op amp launched by Texas Instruments. It is available in 8-pin SO package. Its maximum supply current is 50µA, maximum offset voltage is 70µV, maximum offset current is 250pA, maximum input voltage range is -0.3V~+15V, maximum output voltage range is -0.3V~+15V, and maximum output current is 5mA.
LINEAR TECHNOLOGY LT1769 1769fa Constant-Current/ Constant-Voltage 2A Battery Charger with Input Current Limiting handbook
LT1769 1769fa Constant-Current/ Constant-Voltage 2A Battery Charger with Input Current Limiting
LINEAR TECHNOLOGY LT1640AL/LT1640AH Negative Voltage Hot Swap Controller handbook
The LT1640AL/LT1640AH are 8-pin, negative voltage Hot SwapTM controllers that allow a board to be safely inserted and removed from a live –48V backplane. Inrush current is limited to a programmable value by controlling the gate voltage of an external N-channel pass transistor. The pass transistor is turned off if the input voltage is less than the programmable undervoltage threshold or greater than the overvoltage threshold. A programmable electronic circuit breaker protects the system against shorts. The PWRGD (LT1640AL) or PWRGD (LT1640AH) signal can be used to directly enable a power module. The LT1640AL is designed for modules with a low enable input and the LT1640AH for modules with a high enable input. The LT1640AL/LT1640AH are available in 8-pin PDIP and SO packages.
LINEAR TECHNOLOGY LTC6900 Manual
The LTC6900 is a precision, low power oscillator that is easy to use and occupies very little PC board space. The oscillator frequency is programmed by a single external resistor (RSET). The LTC6900 has been designed for high accuracy operation (≤1.5% frequency error) without the need for external trim components. The LTC6900 operates with a single 2.7V to 5.5V power supply and provides a rail-to-rail, 50% duty cycle square wave output. The CMOS output driver ensures fast rise/fall times and rail-to-rail switching. The frequency-setting resistor can vary from 10kΩ to 2
LINEAR TECHNOLOGY LTC2430/LTC2431 Manual
LTC2430/LTC2431 are 2.7V to 5.5V micropower 20-bit differential ∆Σ analog-to-digital converters with an integrated oscillator, 3ppm INL and 0.56ppm RMS noise. They use delta-sigma technology and provide single cycle settling time for multiplexed applications. Through a single pin, the LTC2430/LTC2431 can be configured for better than 110dB differential mode rejection at 50Hz or 60Hz ±2%, or they can be driven by an external oscillator for a user-defined rejection frequency. The internal oscil- lator requires no external frequency setting components. The converters accept any external differential reference voltage from 0.1V to VCC for flexible ratiometric and remote sensing measurement configurations. The full- scale differential input range is from –0.5VREF to 0.5VREF. The reference common mode voltage, VREFCM, and the input common mode voltage, VINCM, may be indepen- dently set anywhere within GND to VCC. The DC common mode input rejection is better than 120dB. The LTC2430/LTC2431 communicate through a flexible 3-wire digital interface that is compatible with SPI and MICROWIRE TM protocols.
LINEAR TECHNOLOGY LTC1877 Manual
The LTC1877 is a high efficiency, low quiescent current, synchronized, burst mode synchronous buck regulator.
LINEAR TECHNOLOGY LT1725 General Purpose Isolated Flyback Controller Manual
The LT1725 is a monolithic switching regulator controller specifically designed for the isolated flyback topology. It drives the gate of an external MOSFET and is generally powered from a third transformer winding. These features allow for an application input voltage limited only by external power path components. The third transformer winding also provides output voltage feedback information, such that an optoisolator is not required. Its gate drive capability coupled with a suitable external MOSFET can deliver load power up to tens of watts. The LT1725 has a number of features not found on most other switching regulator ICs. By utilizing current mode switching techniques, it provides excellent AC and DC line regulation. Its unique control circuitry can maintain regulation well into discontinuous mode in most applications. Optional load compensation circuitry allows for improved load regulation. An optional undervoltage lockout pin halts operation when the application input voltage is too low. An optional external capacitor implements a soft-start.
LINEAR TECHNOLOGY LT1959 Manual
LINEAR TECHNOLOGY LT1424-5 Manual
The LT1424-5 is a monolithic high power switching regulator specifically designed for the isolated flyback topology. No “third winding” or optoisolator is required; the integrated circuit senses the isolated output voltage directly from the primary side flyback waveform. A high current, high efficiency switch is included on the die along with all oscillator, control and protection circuitry. The LT1424-5 operates with input supply voltages from 3V to 20V and draws only 7mA quiescent current. It can deliver up to 400mA at 5V with no external power devices. By utilizing current mode switching techniques, it provides excellent AC and DC line regulation. The LT1424-5 has a number of features not found on other switching regulator ICs. Its unique control circuitry can maintain regulation well into discontinuous mode. Load compensation circuitry allows for improved load regulation. An externally activated shutdown mode reduces total supply current to 20µA typical for standby operation.